READING
To use the broadband router, you must properly configure the network settings of your PCs and install the in
-
cluded setup program to setup the print server.
Configure the network settings
If the TCP/IP protocol is not yet configured on your PC, refer to the TCP/IP installation procedure below. If the
TCP/IP protocol is configured, perform the following steps to configure the broadband router:
1. In Windows 95, 98, and Me, click Windows
Start
and then
Run
. In the
Run
dialog box, type winipcfg and
click
OK
. In Windows NT and 2000, click Windows
Start
and then
Run
. In the
Run
dialog box, type command
and click
OK
. Then click Windows
Start
and then
Run
again. Type ipconfig and click
OK
.
2. When the IP Configuration window comes up, select your network adapter from the drop-down menu. After
you select your network adapter, the correct information for your broadband router and network connection will
be displayed. The default IP address of your Ethernet card should be 192.168.123.xxx, where xxx is any value
between 100 and 199. The default subnet mask is 255.255.255.0 and the default gateway is 192.168.123.254. If
the correct values are not shown, click
Release
and then click
Renew
. If the correct values are still not shown,
proceed to the Troubleshooting section in this manual. Click
More Info
and write down the various addresses
that are listed.
If the TCP/IP protocol is not configured on your PC, perform the following steps:
Installing the TCP/IP protocol into your PC
In Windows 98 and Me: Click Windows
Start
,
Settings
, and then click
Control Panel
. Double-click the
Net
-
work
icon and select the
Configuration
tab in the Network window. Click
Add
to add the network component
into your PC. Double-click
Protocol
to add the TCP/IP protocol. Select Microsoft in the Manufacturers list.
Choose TCP/IP in the Network Protocols and click
OK
to return to the Network window. The TCP/IP protocol
will be listed in the Network window. Click
OK
to complete the installation procedure, then you must restart
your PC.
In Windows 2000: Click Windows
Start
,
Settings
, and then click
Control Panel
. Double-click
Network
.
Double-click
Local Area Connection
and then click
Properties
. Click
Install
, click
Protocol
, and then click
Add
. Click
TCP/IP
and then click
Add
.
In Windows NT: Click Windows
Start
,
Settings
, and then click
Control Panel
. Double-click
Network
. Click
Protocols
and click
Add
. Select
Microsoft
, select
TCP/IP
, then click
Close
. Reapply any service packs, then
restart your PC.
Setting the TCP/IP protocol to work with the broadband router
1. Click Windows
Start
,
Settings
, then click
Control Panel
.
2. Double-click the
Network
icon. Click the
Configuration
tab
and select the TCP/IP line that has been as
-
signed to your network card.
3. Click the
Properties
button to set the TCP/IP protocol for the broadband router.
4. There are two setting methods to configure the IP:
To obtain the IP automatically through the DHCP server, perform the following steps:
Click the
IP Address
tab, and select
Obtain an IP address automatically
.
To configure the IP manually, perform the following steps:
a. Click the
IP Address
tab. Click
Specify an IP address
. Enter values in the IP Address field and in the Subnet
Mask field. The default IP address of this product is 192.168.123.254. You should use 192.168.123.xxx (xxx is
between 100 and 199) for IP Address field and 255.255.255.0 for Subnet Mask field.
b. Click the
Gateway
tab. Add the IP address of this product (default IP is 192.168.123.254) in the New gateway
field and click
Add
.
Contact your ISP to get the necessary DNS values. Click the
DNS Configuration
tab. Add the DNS values into
the DNS Server Search Order field and click
Add
.
Broadband Router User Guide
R24.0031.00 (Windows 95, 98, 2000, NT, Me, and Macintosh)
5
10
15
20
25
1
30
35
40
45
