Raytheon Anschütz NautoPilot 5000 Series Скачать руководство пользователя страница 166

Страница: 166 / 191

NautoPilot® 5000 Series
102-890.NG001-NG003
Operator Manual

10000001052

150

Edition: 003

6.4 Handling of more than one NautoPilot® Operator Unit in a steering

system (Master - Master - application)

It is possible to install more than one Master NautoPilot® Operator Unit in a steering

system (if there are 2 or more complete independent steering positions - for

example).

6.4.1

Specifics for a Master - Master - Application

Each NautoPilot® Operator Unit is complete independent, with

own sets of parameters and adjustments.

Each NautoPilot® Operator Unit must be switched on separately for usage.

Both (or more) NautoPilot® Operator Units must be switched on for operation.

A switching over (Master to Master) is possible only in Heading Control mode of

the Source- Master.

The Destination- Master starts in Heading Control mode and controls with its own

parameters and adjustments.

Occurred alerts are

not

transmitted from the Source-

Master to the Destination- Master.

A switching over with an Override function is performed to the last active Master

only.

If this Master is currently not active, an alarm is generated at an Override Signal
Unit.

A switching over is performed only by activation of the other Autopilot Operator

Unit (pressing the Heading button).

Each NautoPilot® Operator Unit must be operated separately according to this

manual.

Содержание NautoPilot 5000 Series
































































































































































































Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды

Raytheon Anschütz NautoPilot 5000 Series, Руководство оператора

Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды