Raytheon Anschütz NautoPilot 5000 Series Скачать руководство пользователя страница 163

Страница: 163 / 191

NautoPilot® 5000 Series

102-890.NG001-NG003

Operator Manual

Edition: 003

147

10000001052

for Track Control mode.

General information:

At the active NautoPilot® Operator Unit a green LED is on at the

corresponding mode button.

At the inactive NautoPilot® Operator Units a yellow LED is on at the

corresponding mode button.

Green LED (off) and yellow LED (off) show the Manual

mode. Green LED (off) and yellow LED (on) show the

Standby mode.

6.3.1

OU Display indication

This information is displayed at an inactive NautoPilot® Operator Unit only if

there are more than one NautoPilot® Operator Units in a steering system (refer

to Figure 59).

It means that this NautoPilot® Operator Unit serves only as a display.

At this NautoPilot® Operator Unit no inputs are possible (except

acknowledgement of messages in the message bar).

But a selection of other displays is possible.

Figure 66:

Indication OU Display” in

slave operator unit

Содержание NautoPilot 5000 Series
































































































































































































Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды

Raytheon Anschütz NautoPilot 5000 Series, Руководство оператора

Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды