Raytheon Anschütz NautoPilot 5000 Series Скачать руководство пользователя страница 146

Страница: 146 / 191

NautoPilot® 5000 Series
102-890.NG001-NG003
Operator Manual

10000001052

130

Edition: 003

5 Description Additional Autopilot Control Unit (AACU)

With the Additional Autopilot Control Unit, it is possible to control the NautoPilot®

in the modes:

- Heading Control

- and Course Control.

In addition, a Curved Heading Line is displayed in the Raytheon SYNAPSIS NX

ECDIS and RADAR systems.

5.1 Switching ON / OFF

After switching on the supply voltage (24 V DC) at a main switch board the

NautoPilot® Operator Unit and the Additional Autopilot Control Unit is switched on.

There is no separate ON/OFF switch.

For switching OFF, the supply voltage at a main switch board must be switched OFF.

Содержание NautoPilot 5000 Series
































































































































































































Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды

Raytheon Anschütz NautoPilot 5000 Series, Руководство оператора

Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды