Raytheon Anschütz NautoPilot 5000 Series Скачать руководство пользователя страница 132

Страница: 132 / 191

NautoPilot® 5000 Series
102-890.NG001-NG003
Operator Manual

10000001052

116

Edition: 003

Table 28

Procedure to switch off Course Control mode in standalone application

Standalone application

HAND

AUTO

Switching the ”Main Steering Switch” into position HAND,

switches the Autopilot to ”Standby”.

The lower LED for standby will light up. The mode change is
displayed at the top right corner of the display
(Course Ctrl.

→

Standby).

Note:
Switching the ”Main Steering Switch” into position AUTO,

switches the Autopilot to ”Heading Control” again.

Tiller

Activating a

”Tiller” (no NautoSteer Tiller) with an override

function, changes the Autopilot mode to Override”.
I.e. the Autopilot is not in control of the rudder.

Observe section 1.4.8.

Note:
With a connected Override Operator Panel the Autopilot can
be activated aga

in and starts in Heading Control” mode.

The lower LED will light up.
The mode change is displayed at the top right corner of the
display (Course Ctrl.

→

Override).

4.4.3

Procedure to switch from Track Control mode to Course Control mode

It is

not

possible to switch directly from Track Control mode to Course Control mode

. It is only possible to switch from Heading Control mode to Course Control mode.

4.4.4

Switching off Course Control mode

It is not possible to switch off Course Control mode - only switching over to other

control modes or to a steering mode (manual) is possible:

- For switching over to Heading Control, see section 4.3.3.

- For switching over to Standby, Override or Manual see instructions below

Содержание NautoPilot 5000 Series
































































































































































































Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды

Raytheon Anschütz NautoPilot 5000 Series, Руководство оператора

Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды