background image

Quick Start 

Safety Information: 

White

-

Light

,

 

730nm 

and IR Variants (850nm & 940nm) 

Caution – Risk Group 2. Avoid Exposure / use protection.  

See Safety Information in FULL Instruction Guide for details. 

Box Contents:

VARIO2 Illuminator with 35° ILS fitted, spare 60° beam angle ILS, User Guide 

(ILS: Interchangeable Lens  System)  

Optional Accessories:  Remote Controller for additional programming,   

80˚ beam angle ILS, 120˚ beam angle ILS, Bracketry 

Factory Default Set-Up: 

35˚ Beam Angle ILS, Max 100% Power 

Telemetry Input – closed, Photocell sensitivity – MID 

Status LEDs – ON, No PIN Set 

Unit will change from Programming Mode to Operating Mode after 7 Days (or 30 

minutes after last press of manual buttons

)

 

Timer Disabled

VARIO2 Specifications Table:

 

i16 

w16 

  i8 

w8 

i6 

i4 

w4 

  i2 

w2 

Consumption 

100W 

max 

84W 

max 

46W 

max 

42W 

max 

25W 

max 

13W 

max 

24W 

max 

10W 

max 

11W 

max 

Input 

24V AC/DC 

12/24V AC/DC 

12/24V AC/DC 

12/24V AC/DC 

Weight 

3.1kg  (6.8lbs) 

1.65kg (3.61lbs) 

950g  (2.1lbs) 

600g  (1.3lbs) 

Number of 

LED’s 

48 

24 

12 

12 

Environment 

IP66 

IP66 

IP66 

IP66 

Dimensions 

180 x 277 x 75mm 

7”x11”x2.9” 

135 x 180 x 68mm 

(5”x7”x3”) 

100 x 135 x 66m 

4”x5”x2.5”) 

75 x 100 x 64mm 

3”x4”x2.5”) 

Cable Length 

2.5m 

2.5m 

2.5m 

2.5m 

2.5m 

2.5m 

2.5m 

2.5m 

2.5m 

Ver

. 10

/1

9

 

Содержание VARIO2 VAR2-i2-2


















Отзывы: