Raytec VAR2 IPPOE i4-1 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 64

Raytec VAR2 IPPOE i4-1 Скачать руководство пользователя страница 6

6

Wiring

The illuminator is supplied with a terminated CAT 5 cable with a waterproof Ethernet

connector (supplied loose i.e. not fitted) and an auxiliary multi-core cable.

Option 1 – Power via PoE

Connect an Ethernet cable (category 5 or better) using the T-568B wiring standard
between the Power Sourcing Equipment (PSE) and the illuminator. Ensure that the
PSE is sufficiently rated to power the VARIO2 IPPoE device as follows:

Model

PoE Requirement

VAR2-IPPoE-w4-1, i4-1, i4-1-C, i6-1

IEEE 802.3at (HP PoE) ≥25.5W

VAR2-IPPoE-w8-1, i8-1, i8-1-C

4-pair PoE ≥51W

The CAT5 cable is both the power and data connection for the illuminator. The

maximum Ethernet cable length is 100m (328 ft) without boosting the signal.

Ensure you make a waterproof connection to the RJ45 as shown below. Ensure the

connector is waterproof and sealed after the connection is made.

To illuminator RJ45-RJ45 connector To Network

Option 2 – Power from 24V DC

If using low voltage power, connect

24V DC

to the red (+ve) and black (-ve) cables of

the auxiliary cable. In this case the Ethernet cable is a data connection only.

For either Option 1 or Option 2 above, connect external input trigger and external

output as required – see table below:

«
...
4
5
6
7
8
...
»

Содержание VAR2 IPPOE i4-1

































































Отзывы:

Нет отзывов