Raymarine SeaNet-Alarm Скачать руководство пользователя | Manualshive

Страница: 12 / 19

background image

SeaNet-Alarm Users Manual

Configuration window

When a port is selected and the programme ist connected to SeaNet-Alarm ( ), the
configuration window will be activated by pressing

.

Main config Window

The software will read the current setting from SeaNet-Alarm.
Changes in the settings are sent to SeaNet-Alarm by pressing
As long as

is not pressed, changes will not be transferred to SeaNet-Alarm.

SeaNet-Alarm V1.0

Page 12 of 19

«
...
10
11
12
13
14
...
»

Содержание SeaNet-Alarm




















Отзывы:

Нет отзывов

Похожие инструкции для SeaNet-Alarm

Бренд: FagronLab Страницы: 16

Бренд: iGuzzini Страницы: 20

Бренд: EarthQuake Страницы: 28

Бренд: TAIKO Audio Страницы: 24

Бренд: Facnor Страницы: 33

Бренд: Dawn Страницы: 8

Бренд: BACtrack Страницы: 13

Бренд: Badgematic Страницы: 28

Бренд: BACtrack Страницы: 2

Бренд: MADRIX Страницы: 28

Бренд: BACTcontrol Страницы: 28

Бренд: Waters Страницы: 4

Бренд: Waterpik Страницы: 2

Бренд: Agilent Technologies Страницы: 114

Бренд: Frick Страницы: 36

Ribiland PR4EN1ELEC

Бренд: Ribimex Страницы: 68

Бренд: Gastrodomus Страницы: 22

FOT-930 MaxTester

Бренд: EXFO Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды