manualshive.com logo in svg

Raymar 3460, Руководство пользователя, Страница: 148 / 171

Поделиться
Скачать
Raymar 3460 Скачать руководство пользователя страница 148

3460 Fast’R

C-12

A stand-alone modem includes a power transformer. The unit conditions 
the power supply. 

The off-line configuration (OLC) button is on the back panel of some 
stand-alone modems. 

Pressing the button makes the modem enter command mode, in which 
the user in synchronous or leased-line environments can change 
configuration options. 

Cards and stand-alone modems

 have the following front panel 

interfaces (Figure C-2 and Figure C-3).

Power Requirements

Characteristic

Requirement at Main 

Supply

Requirement at 

Modem Input

Voltage

100/120/230/240 VAC*

9 VAC

Frequency

50/60 Hz

50/60 Hz

Input Current

150/120/80/70 mA

800 mA

*The power transformer is rated for one of these settings.

Changing a Configuration With the OLC Button

Step

Stage

1.

Change one or more configuration options.

2.

Enter the Save to Option Set command (AT&W

n

, where 

n 

is 1 or 2)

.

3.

Enter the Option Set to Power Up In command (AT&Y

n

, where 

n

 is: 

0 for last-loaded option set; 1 for Option Set 1, or 2 for Option Set 2)

4.

Press the OLC button. The modem restarts and powers up using the 
selected configuration option set.

Содержание 3460












































































































































































Отзывы:

Нет отзывов