Raymar 3460 Скачать руководство пользователя страница 146

Страница: 146 / 171

3460 Fast’R

C-10

The stand-alone modem rear panel has two RJ-11 telephone connectors,
labelled LINE and PHONE.

Telephone Connectors, Modems That Support Two-Wire
Leased or Dial Connections

LINE* Connector

Interface

: RJ-11

Connection Type

: Two-Wire Leased-Line or Dial Line

Pin Function

Telset Ring (Alternative)

Two-wire Leased Line/Dial-Line Ring

Two-wire Leased Line/Dial-Line Tip

Telset Tip (Alternative)

PHONE Connector

Interface

: RJ-11

Connection Type

: Telephone

Pin Function

Telset Ring

Telset Tip

*Pins 2 and 5 are disconnected in some units.

Pins not listed here are not used.

Telephone Connectors, Modems That Support Two- or Four-
Wire Leased or Dial Connection s

PHONE/LINE Connector

Interface

: RJ-11

Connection Type

: Dial Line and Telephone Set

Pin Function

Telset Ring

Dial-Line Ring

Dial-Line Tip

Telset Tip

Содержание 3460












































































































































































Результаты поиска

Содержание 3460

Отзывы:

Raymar 3460, Руководство пользователя, Страница: 146 / 171

Результаты поиска

Содержание 3460

Отзывы: