Raymar 3460 Скачать руководство пользователя страница 127

Страница: 127 / 171

3460 Fast’R

B-27

Test

=End Test

=Initiate Local Analog Loopback (LAL)

=Initiate Local Digital Loopback (LDL).

Note

: this test

is not supported in Reliable mode (AT*SM2)

=Accept Remote Digital Loopback (RDL)=On

=Accept Remote Digital Loopback (RDL)=Off

=Initiate Remote Digital Loopback (RDL)

=Initiate Remote Digital Loopback (RDL) Pattern

=Initiate Local Analog Loopback (LAL) Pattern

Status Message

=Long Form

=Short Form

Save Changes

Saves changes to a option sets made with AT commands.
(If you do not save the changes made with AT
commands, the modem does not store them in
nonvolatile memory.) After selecting an option set
(ATZ

n; n

=0, 1, or 2), and changing options, enter

AT&W

. The modem displays

Saving Options

, then

Save Completed

0 or 1

=Save changes to Option Set 1

=Save changes to Option Set 2

Clock Signal Source

Sets modem timing. Applies to synchronous
applications. For most dial applications, use option 0.

=Internal. The modem uses timing signals passed on
EIA/TIA 232-D Pin 15 (V.24 circuit 114).

=External. The modem uses external timing signals
passed on EIA/TIA 232-D Pin 24 (V.24 circuit 113).

=Loopback. The modem uses loopback timing signals
passed on EIA/TIA 232-D Pin 17 (V.24 circuit 115).

AT Command Set

(continued)

Command

Option

Description

The characters

precede all commands except:

+++

#####

, and

Parameters and options shown shaded gray vary by country. For your country’s options,
refer to the

3460 Fast’R Reference Guide

(TEL–T0022).

Default (pre-set) options are underlined.

Содержание 3460












































































































































































Результаты поиска

Содержание 3460

Отзывы:

Raymar 3460, Руководство пользователя, Страница: 127 / 171

Результаты поиска

Содержание 3460

Отзывы: