Raymar 3460 Скачать руководство пользователя страница 107

Страница: 107 / 171

3460 Fast’R

B-7

=Enable. Data compression is attempted.

If the modem is using LAPM error correction, it uses
V.42bis data compression when

=Enabled.

Note:

an application with SDC enabled, LAPM error
correction and V.42bis data compression

only

are used.

With MNP error correction, the modem attempts to
negotiate V.42bis and MNP-5 data compression with the
remote modem.

Depending on which data compression type the remote
modem can accommodate, V.42bis or MNP-5 is used.
Otherwise, no data compression is used.

Dial Wait Period (Pause After Dialing)

The modem waits 2 seconds for a dial tone.

The modem waits 3 seconds for a dial tone.

The modem waits 4 seconds for a dial tone.

The modem waits 6 seconds for a dial tone.

The modem waits 12 seconds for a dial tone.

The modem waits 15 seconds for a dial tone.

The modem waits 20 seconds for a dial tone.

The modem waits 30 seconds for a dial tone.

The modem waits 40 seconds for a dial tone.

Dial wait is determined by setting S-Register 7.

DTE (Computer) Port Rate

=75 BPS

=150 BPS

=300 BPS

=600 BPS

=1.2 KBPS

=2.4 KBPS

=4.8 KBPS

=7.2 KBPS

AT Command Set

(continued)

Command

Option

Description

The characters

precede all commands except:

+++

#####

, and

Parameters and options shown shaded gray vary by country. For your country’s options,
refer to the

3460 Fast’R Reference Guide

(TEL–T0022).

Default (pre-set) options are underlined.

Содержание 3460












































































































































































Результаты поиска

Содержание 3460

Отзывы:

Raymar 3460, Руководство пользователя, Страница: 107 / 171

Результаты поиска

Содержание 3460

Отзывы: