Raycus RFL-P500 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 27

Raycus RFL-P500 Скачать руководство пользователя страница 17

Wuhan Raycus Fiber Laser Technologies Co., Ltd.

User Guide of RFL-P500

13

1.

REM/OFF/ON:

Key switch, the power switch of the laser. Insert the

key and then turn the key clockwise to the 'ON' to active the laser.

2.

POWER:

Power Indicator, indicates that the power is switched on

when the green LED illumines.

3.

LASER:

Laser emission button, it’s a button with an red LED indicator.

In RS-232 mode and AD mode, when this button is pressed down, the

product is ready to emit laser, and the LED illumines. Press again will

release the button, and disable the laser emission.

4.

ALARM:

Alarm indicator, indicates a fault condition when the yellow

LED illumines.

5.

EMERGENCY STOP:

Press it down to stop the laser immediately.

Turn it clockwise to release, but the laser cannot start before it’s

powered on with key switch for a second time.

4.2

Rear Panel

Figure 5 shows the rear panel:

Figure 5: Rear Panel

1.

INPUT:

The socket for supply input that can be only mated with the

plug on the power cord we provided.The socket is provided with a

«
...
15
16
17
18
19
...
»

Содержание RFL-P500




























Отзывы:

Нет отзывов