Raycus RFL-C1500X Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 40

background image

Wuhan Raycus Fiber Laser Technologies Co., Ltd.

User Guide of RFL- RFL-C1500X/C2000X

WARNING:

Any interruption from the protective earth will electrify

the enclosure, which may result in personal injury.

(2) Make sure that the correct voltage of the AC power source is used.

CAUTION:

Failure to connect the correct voltage could damage the

product.

1.6 Other Safety Rules

(1) Never look directly into the laser output port when power is supplied to the laser.

(2) Avoid using the laser in a dim or darkened environment.

(3) If this device is used in a manner not specified in this document, the protection provided

by the device may be impaired and the warranty will be voided.

(4) There are no operator serviceable parts inside, and all maintenance must be performed

in Raycus or by qualified Raycus personnel. Do not try to remove covers, or electrical shock

may be caused, and warranty will be void.

«
...
5
6
7
8
9
...
»

Содержание RFL-C1500X









































Отзывы:

Нет отзывов

Похожие инструкции для RFL-C1500X

Бренд: Xantrex Страницы: 2

Бренд: Xaoc Devices Страницы: 8

Бренд: PCE Health and Fitness Страницы: 11

Бренд: YOSensi Страницы: 27

Бренд: Scheppach Страницы: 20

Бренд: jbc Страницы: 12

Бренд: Lisle Страницы: 8

Pure Resonator BB

Бренд: K&K Sound Страницы: 4

Бренд: Agilent Technologies Страницы: 79

Бренд: TESTO Страницы: 4

Бренд: HEIDENHAIN Страницы: 28

Бренд: K&K Sound Страницы: 2

Бренд: H Heuer Instruments Страницы: 104

Бренд: Orla Страницы: 44

Soundpro DL Series

Бренд: TSI Quest Страницы: 8

Бренд: Instantel Страницы: 90

HYDROSPLIT R 21

Бренд: B meters Страницы: 100

Бренд: cam Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды