manualshive.com logo in svg

Raven Sidekick Pro, Руководство по установке и эксплуатации

Поделиться
Скачать
Raven Sidekick Pro Скачать руководство пользователя страница 44

CHAPTER 5

42

SideKick Pro™ ICD 1-40 oz./min. and 5-200 oz./min. Installation & Operation Manual

DIAGNOSTIC TROUBLE CODES

The Diagnostic Trouble Code (DTC) list provides a list of recent errors for the equipment operator. access the DTC 

list to review the previous error conditions, the tally for each condition, during operation. Refer to DTC section in 

Chapter 7, 

Troubleshooting

, for additional information on Diagnostic Trouble Codes.

CLEAR DIAGNOSTIC TROUBLE CODES

Press the Clear DTCs icon to clear the diagnostic trouble codes.

VIEW DTC INFO

Press View DTC Info to view the alarm mask associated with the highlighted active DTC.

VIEW ACTIVE DTCS

Shows the SPN and FMI for all the active DTCs along with a short description and the number of times this error 

occurred.

VIEW INACTIVE DTCS

Shows the SPN and FMI for all of the inactive DTCs along with a short description and the number of times the 

error occurred.

Содержание Sidekick Pro

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды