Raven Sidekick Pro Скачать руководство пользователя страница 38

Страница: 38 / 64

CHAPTER 5

SideKick Pro™ ICD 1-40 oz./min. and 5-200 oz./min. Installation & Operation Manual

TABLE 6.

Device Totals

SYSTEM INFORMATION

1. Open the UT Menu and select the desired Sidekick Pro™ ICD Menu icon.
2. Select the Diagnostics icon.
3. Select Product Information.
4. Select the desired information from the drop-down. The options are:

•

Hardware/Software

•

System Readings

•

System Hours

•

CAN Bus Information

•

Reset Defaults

HARDWARE/SOFTWARE

This screen includes the Hardware Part Number, Hardware Serial Number, Hardware Revision, Software Part

Number.

SYSTEM READINGS

This screen displays the ECU Power, Motor Power, and ECU Temperature.

SYSTEM HOURS

This screen shows the Software Hours and Engaged Hours.

CAN BUS INFORMATION

The CAN Bus Information screen shows CAN Address, Instance Number, and Extended Identify Number.

Display

Icon

Description

Device Volume

This register keeps a running tally of the operating

life of the system. Cannot be reset by the machine

operator.

Engaged Hours

Displays the amount of time the pump has actively

pumping product.

Software Hours

Displays the amount of time the software has been

on the injection pump.

Area

The total area covered by the system.

Sidekick Pro

ICD Menu

Product

Information

Diagnostics

Содержание Sidekick Pro
































































Результаты поиска

Содержание Sidekick Pro

Отзывы:

Бренды по названию

Популярные бренды

Raven Sidekick Pro, Руководство по установке и эксплуатации

Результаты поиска

Содержание Sidekick Pro

Отзывы:

Бренды по названию

Популярные бренды