manualshive.com logo in svg

Raven Sidekick Pro, Руководство по установке и эксплуатации

Поделиться
Скачать
Raven Sidekick Pro Скачать руководство пользователя страница 37

5

Calibration and Operation: Sidekick Pro™ ICD Menu

35

CALIBRATION AND OPERATION

CURRENT TOTALS DATA

1. Open the UT Menu and select the desired Sidekick Pro™ ICD menu icon.
2. Select the Totals Data icon then Current Totals. The following information will display:

TABLE 5. 

Current Totals

DEVICE TOTALS

1. Open the UT Menu and select the desired Sidekick Pro™ ICD menu icon.
2. Select the Totals Data icon then Device Totals. The following information will display:

Display

Icon

Description

Actual Flow

Displays the actual flow rate of the pump during operation.

Target Flow

Use this field to enter the target flow rate of the pump set 

from the controlling ECU.

Tank Percentage

Displays the current percentage of the tank volume to the 

tank capacity.

Pressure

Displays the pressure at the injection pump pressure 

transducer.

Current Volume

Displays the volume or product dispensed during a field 

operation and is resettable by the user.

Actual Rate

Displays the actual rate of injection during operation.

Target Rate

Use this field to enter the target rate of injection for field 

operation.

Area per Hour

Displays the current rate at which area is covered.

Area Remaining

Displays the calculated area that can be covered with the 

volume of product remaining in the tank.

Speed

The speed of the machine reported via the ISOBUS system.

Area

The total area covered since the last time the tally was reset.

Sidekick Pro 

ICD Menu

Totals 

Data

Current Totals

Sidekick Pro 

ICD Menu

Totals 

Data

Device Tools

Содержание Sidekick Pro

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды