background image

CHAPTER

1

Important Information: Safety

1

CHAPTER 1

IMPORTANT INFORMATION

SAFETY

Follow the operation and safety instructions included with the implement and/or controller and read this manual 

carefully before installing or operating this Raven system.
• Follow all safety information presented within this manual. Review implement operation with your local dealer.
• Contact a local Raven dealer for assistance with any portion of the installation, service, or operation of Raven 

equipment.

• Follow all safety labels affixed to system components. Be sure to keep safety labels in good condition and 

replace any missing or damaged labels. Contact a local Raven dealer to obtain replacements for safety labels.

Observe the following safety measures when operating the implement after installing this Raven system:
• Do not operate this Raven system or any agricultural equipment while under the influence of alcohol or an 

illegal substance.

• Be alert and aware of surroundings and remain in the operator seat at all times when operating this Raven 

system.

Do not operate the implement on any public road with this Raven system enabled.

Disable this Raven system before exiting the operator seat.

Determine and remain a safe working distance from obstacles and bystanders. The operator is 

responsible for disabling the system when a safe working distance has diminished.

Disable this Raven system prior to starting any maintenance work on the implement or components 

of this Raven system.

• Do not attempt to modify or lengthen any of the system control cables. Extension cables are available from a 

local Raven dealer.

AGRICULTURAL CHEMICAL SAFETY

Follow all federal, state, and local regulations regarding the handling, use, and disposal of agricultural chemicals, 

products, and containers. Triple-rinse and puncture or crush empty containers before properly disposing of them. 

Contact a local environmental agency or recycling center for additional information.
• Always follow safety labels and instructions provided by the chemical manufacturer or supplier.

NOTICE

 

WARNING

Содержание RCM































Отзывы: