manualshive.com logo in svg

Raven Case IH Patriot 3XX0, Руководство по установке системы управления и навигации

Поделиться
Скачать
Raven Case IH Patriot 3XX0 Скачать руководство пользователя страница 19

3

016-5032-103 Rev. D

15

HYDRAULIC SYSTEM INSTALLATION

FIGURE 6. Pressure Hose Installed

3. Install a -6 ORFS M/M/F swivel run tee adapter fitting (P/N 333-0012-069) on the steel pressure line.
4. Connect the machine’s pressure hose to the opposite end of the installed tee fitting.
5. Install the 90° end of the supplied hydraulic hose (P/N 214-1000-318) on the 90° end of the installed tee fitting.
6. Connect the straight end of the installed hydraulic hose to Port P of the steering valve.

INSTALL THE TANK HOSE

1. Locate the machine’s steel tank line.

NOTE:

The pressure line runs on the inside of the frame from the rear of the machine. Trace it to the T port 

on the steering orbital if necessary.

2. Disconnect the machine’s tank hose from the steel tank line.

FIGURE 7. Tank Hose Installed

3. Install a -8 ORFS M/M/F swivel run tee adapter fitting (P/N 333-0012-028) on the machine’s steel tank line.
4. Connect the machine’s tank hose to the opposite end of the installed tee fitting.
5. Install the -8 end of the supplied hydraulic hose (P/N 214-1000-630) on the 90° end of the installed tee fitting.
6. Connect the other end of the installed hydraulic hose to Port T of the steering valve.

Содержание Case IH Patriot 3XX0











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды