manualshive.com logo in svg

Raven AutoBoom XRT, Калибровка и руководство по эксплуатации

Поделиться
Скачать
Raven AutoBoom XRT Скачать руководство пользователя страница 5

CHAPTER

1

P/N 016-0235-001 Rev. B

1

CHAPTER 1

IMPORTANT SAFETY 

INFORMATION

Read this manual and the operation and safety instructions included with your implement and/or controller 

carefully before installing the AutoBoom XRT system.
• Follow all safety information presented within this manual.
• If you require assistance with any portion of the installation or service of your Raven equipment, contact your 

local Raven dealer for support.

• Follow all safety labels affixed to the AutoBoom XRT system components. Be sure to keep safety labels in good 

condition and replace any missing or damaged labels. To obtain replacements for missing or damaged safety 

labels, contact your local Raven dealer.

When operating the machine after installing AutoBoom XRT observe the following safety measures:
• Be alert and aware of surroundings.
• Do not operate XRT or any agricultural equipment while under the influence of alcohol or an illegal substance.
• Remain in the operator’s position in the machine at all times when AutoBoom XRT is engaged.
• Disable XRT when exiting the operator’s seat and machine.
• Do not drive the machine with AutoBoom XRT enabled on any public road.
• Determine and remain a safe working distance from other individuals. The operator is responsible for disabling 

XRT when the safe working distance has diminished.

• Ensure XRT is disabled prior to starting any maintenance work on the system or the machine.

• Carefully read and follow all safety requirements and precautions contained in this manual and the machine-

specific Installation Manual. Failure to follow safety instructions may lead to equipment damage, personal 

injury, or death.

• When starting the machine for the first time after installing AutoBoom XRT, be sure that all persons stand clear 

in case a hose has not been properly tightened.

• The machine must remain stationary and switched off during AutoBoom XRT installation or maintenance.

NOTICE

 

WARNING

Содержание AutoBoom XRT









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды