Raven AutoBoom 9600 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 79

Raven AutoBoom 9600 Скачать руководство пользователя страница 45

4

Manual No. 016-0230-096

39

POWERGLIDE PLUS

17. Connect the cable connectors to the Right Up and Left Up connectors on the AutoBoom harness (P/N 115-

0230-045 or 115-0230-085) to the installed boom sense adapter cables.

CONNECT THE HARNESS CABLE TO THE IMPLEMENT EXTENSION TEE - GEN II CABLE ONLY

1. Route the harness cable (P/N 115-0230-085) toward the implement extension tee cable.
2. Connect the harness cable to the To Node connector.
3. Remove the terminator from the machine’s chassis harness or the standalone console harness.
4. Install the terminator on the remaining open end of the implement extension tee cable.
5. Refer to the wiring schematic (beginning on page 40) appropriate for the machine’s configuration to route the

implement extension tee cable.

6. Connect the implement extension tee cable to the location determined in the step above.

CONNECT THE HARNESS CABLE TO THE CONTROLLER CABLE - GEN I CABLE ONLY

1. Route the harness cable (P/N 115-0230-045) toward the machine’s cab.
2. Connect the harness cable to the controller cable (P/N 115-0230-007).
3. Tighten the connector screw cap to secure the connection.

CONNECT THE CONTROLLER (IF APPLICABLE) - GEN I CABLE ONLY

1. Route the controller cable (P/N 115-0230-007) into the right side of the machine’s cab.
2. Locate the two controller connectors and connect them to the AutoBoom controller (P/N 063-0130-021).

NOTE:

The AutoBoom controller should be mounted in the machine’s cab so that the machine’s operator

has easy access to it.

CONNECT THE FIELD COMPUTER (IF APPLICABLE)

Refer to the Installation & Operation Manual and the appropriate wiring schematic beginning on page 40 for

installation and wiring instructions for your specific field computer.

CONNECT THE POWER LEADS

1. Locate the power cable that has the power and ground leads at one end.
2. Disconnect the machine’s connectors from the battery terminals.
3. Install the power lead on the positive battery terminal and reinstall the machine’s battery connector.
4. Install the ground lead on the negative battery terminal and reinstall the machine’s battery connector.

«
...
43
44
45
46
47
...
»

Содержание AutoBoom 9600
















































































Отзывы:

Нет отзывов