background image

4

0

Φ6 - 6.35(1/4")

Φ9.52(3/8")

Φ12-12.7(1/2")
Φ15.8-16(5/8")

1.3

0.7

1.6

1.0

1.8

1.0

2.4

2.2

Pipe expanding method

Note:

Improper pipe expanding is the main cause of refrigerant leakage. Please expand
the pipe according to the following steps:

A: Cut the pipe

● Confirm the pipe length according to 

   the distance of indoor unit and 
   outdoor unit.

● Cut the required pipe with pipe cutter.

pipe

pipe cutter

leaning

uneven

burr

B: Remove the burrs

● Remove the burrs with shaper and

   prevent the burrs from getting into 
   the pipe.

downwards

pipe

shaper

C: Put on suitable insulating pipe

D: Put on the union nut

● Remove the union nut on the indoor

   connection pipe and outdoor valve; 
   install the union nut on the pipe.

union pipe

pipe

E: Expand the port

● Expand the port with expander.

Note:

● "A" is different according to the

   diameter, please refer to the sheet 
   below:

expander

hard
mold

pipe

F: Inspection

● Check the quality of expanding port. 

    If there is any blemish, expand the 
    port again according to the steps 
    above.

the length is equal

improper expanding

leaning

damaged

surface

crack

uneven
thickness

smooth surface

Outer diameter

(mm)

A(mm)

Max

Min

Содержание RS-V12KE

















































Отзывы: