Rasilient PixelStor 5000 Скачать руководство пользователя страница 17

Страница: 17 / 161

About This Manual

PixelStor 5000 User Manual
Rev. 1, May 2013

vii

Regulatory and Integration Information

Regulatory Compliance Identification Numbers

For the purpose of regulatory compliance certifications and identification, this system is

assigned a serial number. This system serial number can be found on the product label, along

with the required approval markings and information. When requesting certification information

for this product, always refer to this serial number. This serial number should not be confused

with the marketing name or model number.

Product Regulatory Compliance

Product Safety Compliance

This system complies with the following safety requirements:

Table i Product Safety Requirements

IEC 60950-1

Safety of Information Technology Equipment

EN 60950-1

Safety of Information Technology Equipment Including Electrical Business

Equipment,

European

Committee

for

Electro-technical

Standardization

(CENELEC)

UL 60950-1

Safety of Information Technology Equipment

UL 94

Tests for Flammability of Plastic Materials for Parts in Devices & Appliances

GB4943

Safety of Information Technology Equipment

Worldwide Safety approvals can be supplied upon request. Please contact your sales

representative for approvals.

Product EMC Compliance

This product has been tested and verified to comply with the following electromagnetic

compatibility (EMC) regulations.

Communications Commission Notice

Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has

established Radio Frequency (RF) emission limits to provide an interference-free radio

frequency spectrum. Many electronic devices, including computers, generate RF energy

incidental to their intended function and are, therefore, covered by these rules. These rules

place computers and related peripheral devices into two classes, A and B, depending upon their

Содержание PixelStor 5000


































































































































































Результаты поиска

Содержание PixelStor 5000

Отзывы:

Похожие инструкции для PixelStor 5000

Бренды по названию

Популярные бренды

Rasilient PixelStor 5000, Руководство пользователя

Результаты поиска

Содержание PixelStor 5000

Отзывы:

Похожие инструкции для PixelStor 5000

Бренды по названию

Популярные бренды