Ransomes MP653, Инструкция по безопасности, эксплуатации и техническому обслуживанию/Список запасных частей, Страница: 75 / 138

en-71
ADJUSTMENTS 7
7.6.3 HEIGHT OF CUT ADJUSTMENT (MP653XC WING CUTTER DECKS) __________
1. Raise the deck to mid position.
2. Remove the quick pin (A) from the top of the caster wheel pivot
spindle
3. Remove the caster wheel from caster support (B).
4. Select either Position 1 or Position 2 for wheel mounting bracket (C).
To change, remove (4) mounting bolts (D), move to the alternate
location and bolt in place.
5. Place the selected size and number of spacers (E) below the caster
support. Both A-size (6.5 mm) and B-size (12.5 mm) spacers are
provided. Place the remaining spacers above the caster support.
6. Replace the quick pin.
7. Place pin (F) into the proper hole of bracket for the selected height of
cut and fit quick pin (G).
8. To change level of deck - release nuts (H) locking ball joints in
position and turn the hexagon bar (J) in the center to the right or to
the left side to lift / lower the deck. Fasten when deck is level
Check Wing Deck Chain Tension
1. Put a 27 mm spacer below the deck shell at the side where
the new height of cut Brackets are installed.
2. Make sure the caster wheels are set to the lowest height of
cut before you start.
3. If the rear chain is slack, the serrated plate will have to be
moved lower in the serrated slot.
4. Remove the 27mm spacer below the deck.
5. Repeat the procedure for other wing deck.
A
A
27mm
F
G
A
B
D
C
E
J
G
H
K
S
1
2
B
A
4314591
K
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
0
A [1]
B [1]
A [1] + B [1]
B [2]
A [1] + B [2]
B [3]
A [1] + B [3]
0
A [1]
B [1]
A [1] + B [1]
B [2]
A [1] + B [2]
B [3]
A [1] + B [3]
X1
Y2
X3
Y4
X5
Y6
X7
Y8
X9
Y10
X11
Y12
X13
Y14
X15
Y16
1 - 2 S H
25 mm
31 mm
38 mm
44 mm
50 mm
57 mm
63 mm
69 mm
76 mm
82 mm
88 mm
95 mm
101 mm
108 mm
114 mm
120 mm
1.0 in
1.25 in
1.50 in
1.75 in
2.0 in
2.25 in
2.50 in
2.75 in
3.0 in
3.25 in
3.50 in
3.75 in
4.0 in
4.25 in
4.50 in
4.75 in
K
X1
Y2
X3
Y4
X5
Y6
X7
Y8
X9
H
H
Y
X
Y16
Y15
Y14
Y13
Y10
Y11
Y12
15
13
11
1
9
7
5
3
16
14
12
10
8
6
4
2
S
1
2
B
A
4306795
K
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2 0
A [1]
B [1]
A [1] + B [1]
B [2]
A [1] + B [2]
B [3]
A [1] + B [3]
0
A [1]
B [1]
A [1] + B [1]
B [2]
A [1] + B [2]
B [3]
A [1] + B [3]
X1
Y2
X3
Y4
X5
Y6
X7
Y8
X9
Y10
X11
Y12
X13
Y14
X15
Y16
1 - 2 S H
25 mm
31 mm
38 mm
44 mm
50 mm
57 mm
63 mm
69 mm
76 mm
82 mm
88 mm
95 mm
101 mm
108 mm
114 mm
120 mm
1.0 in
1.25 in
1.50 in
1.75 in
2.0 in
2.25 in
2.50 in
2.75 in
3.0 in
3.25 in
3.50 in
3.75 in
4.0 in
4.25 in
4.50 in
4.75 in
K
H
X1
Y2
X3
Y4
X5
Y6
X7
Y8
X9
H
16
14
12
10
8
6
4
2
X
Y
15
13
11
9
7
5
3
1
X15
X13
Y14
Y16
Y10
X11
Y12