R&S ZNL Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 1135

background image

Getting Started

R&S

®

ZNL/ZNLE

49

User Manual 1178.5966.02 ─ 19

●

This connector is provided by the "Additional Interfaces" option R&S

FPL1-B5.

This option is not available for the R&S

ZNLE.

●

The IF/Video Output interface is only functional in Spectrum mode (option
R&S

ZNL3|4|6-B1)

●

Interruptions in analog output can occur if you switch between a VNA and a spec-
trum application, due to the separate hardware. In particular, if you run a sequence
of measurements including both measurement types, switching between both
modes can interrupt the signal from the output connector.

For details, see the R&S

ZNL/ZNLE Spectrum Mode user manual.

4.2.2.8

Aux. Port

A 25-pole D-Sub connector used as an input and output for low-voltage TTL control
signals. Can either be used as VNA user port (max. 3.3

V) or SA Aux. Port (max. 5

V).

In the firmware GUI, this can be set via [Setup] > "System Config" > "Add Interfaces" >
"Port Configuration".

13

25

1

14

This connector is provided by the "Additional Interfaces" option R&S

FPL1-B5.

For details, see

Chapter 14.2.1.1, "Aux. Port"

This option is not available for the R&S

ZNLE.

Short-circuit hazard

Always observe the designated pin assignment. A short-circuit can damage the port.

4.2.2.9

Headphones connector

The Spectrum mode provides demodulators for AM, FM and PM signals, which can be
routed to the headphone connector. With headphones or an external loudspeaker con-
nected to the 3.5 mm headphone socket, the displayed signal can be identified acousti-
cally.

Instrument tour

«
...
47
48
49
50
51
...
»

Содержание ZNL
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZNL

Бренд: Vcheck Страницы: 31

Бренд: Eagletone Страницы: 2

Бренд: Hammond Страницы: 78

Бренд: Magnescale Страницы: 64

SourceMeter 2430

Бренд: Keithley Страницы: 141

Бренд: Emos Страницы: 76

Бренд: Hanna Instruments Страницы: 52

Recordall Series

Бренд: Badger Meter Страницы: 8

Бренд: Fluke Biomedical Страницы: 28

Бренд: VOLTCRAFT Страницы: 108

Бренд: Wetekom Страницы: 22

Universal Analyzers 275E

Бренд: Ametek Страницы: 34

Бренд: Topcon Страницы: 59

Бренд: SATO KEIRYOKI Страницы: 2

Бренд: Sonel Страницы: 84

Бренд: Agilent Technologies Страницы: 198

Бренд: Laser Technology Страницы: 80

Бренд: Hanna Instruments Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды