R&S ZNL Скачать руководство пользователя страница 340 | Manualshive

Страница: 340 / 1135

background image

VNA GUI reference

R&S

®

ZNL/ZNLE

340

User Manual 1178.5966.02 ─ 19

In particular, it is possible to use two different external trigger sources (R&S

ZNL

only).

Remote command:

TRIGger<Ch>[:SEQuence]:SOURce EXTernal

Manual Trigger

Generates the trigger event for "Manual" trigger mode and is disabled unless this mode
is active.

Remote command:

TRIGger<Ch>[:SEQuence]:SOURce MANual

*TRG

Sequence

Selects the measurement cycle or sequence of actions to be triggered in "External" or
"Manual" mode.

●

"Sweep" means that each trigger event starts an entire sweep, according to the
current sweep configuration.

●

"Point" means that each trigger event starts the measurement at the next sweep
point.

●

"Partial Measurement" means that each trigger event starts the next partial mea-
surement at the current or at the next sweep point. If every sweep point only
requires a single partial measurement, this option is equivalent to "Point".
See also

Chapter 9.1.4.1, "Partial measurements and driving mode"

●

"Segment" means that each trigger event starts the next sweep segment within the
current sweep. If a sweep type other than

is active, this option is equiv-

alent to "Sweep".

Relation with other sweep settings

Some sweep settings are logically incompatible with a particular selection of the trig-
gered measurement sequence:

●

If a

sweep is performed, the sequence is always a sweep.

●

"Alternated"

only makes sense if the triggered measurement

sequence comprises more than one sweep point. If "Point" or "Partial Measure-
ment" is selected, "Alternated" mode is switched off and vice versa.

Note:

The trigger events must be adjusted to the triggered measurement sequence. If

the analyzer receives a trigger event while the last sequence is still running, the
R&S

ZNL/ZNLE skips the trigger event and generates a message.

Remote command:

TRIGger<Ch>[:SEQuence]:LINK

Sweep Softtool

«
...
338
339
340
341
342
...
»

Содержание ZNL
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZNL

Бренд: Eaton Страницы: 53

Бренд: Oceanic Страницы: 75

Бренд: Unico Страницы: 10

Бренд: Zeversolar Страницы: 35

Бренд: Zenner Страницы: 52

Бренд: X-laser Страницы: 17

Frontline 802.11

Бренд: Teledyne Lecroy Страницы: 223

Бренд: Johnson & Associates Страницы: 33

Бренд: PCE Health and Fitness Страницы: 11

SensoControl Serviceman SCM-150 Series

Бренд: Parker Страницы: 39

Бренд: Kawai Страницы: 72

Бренд: SBS Страницы: 17

Бренд: Hach Страницы: 4

Cerabar S PMC71

Бренд: Endress+Hauser Страницы: 48

350 Maritime V2

Бренд: TESTO Страницы: 106

Бренд: Ditel Страницы: 2

Mini-SuperGraph II

Бренд: NOMIS Seismographs Страницы: 44

Бренд: Saab Страницы: 116

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды