R&S 1424.7005.02 Скачать руководство пользователя страница 21

Страница: 21 / 514

Getting Started

R&S

NRX

User Manual 1178.5566.02 ─ 07

3.1.8

Connecting Power Sensors

The R&S NRX supports a wide range of R&S power sensors. See the data sheet for
detailed information.

Depending on the power sensor, you have different choices for connecting power sen-
sors.

3.1.8.1

Sensor Connectors A to D

See

Chapter 3.2.1.1, "Sensor Connector A and B"

on page 24 and

Chapter 3.2.2.7,

"Sensor Connectors C and D"

on page 30.

Suitable for:

●

USB and LAN power sensors

●

R&S

NRQ6

●

R&S

NRP

‑

Zxx power sensors

NRQ6

Frequency Selective Power Sensor

LAN PoE+

Host

Interface

Sample Clock I/O (Default: 120 MHz)

LO I/0

Figure 3-1: Setup with an R&S power sensor (example)

1 = Signal source
2 = R&S power sensor
3 = Host Interface connector
4 = R&S NRP

‑

ZK8

5 = Sensor connector of the R&S NRX
6 = R&S NRX

Use an R&S NRP

‑

ZK8 cable to connect an R&S power sensor to the R&S NRX. If you

use an R&S NRP

‑

ZK6 cable, the reference clock and trigger are not supported.

1. 8

pin female connector of R&S NRP

‑

ZK8:

a) Insert the screw-lock cable connector into the host interface of the R&S power

sensor.

b) Tighten the union nut manually.

2. 8

pin male connector of R&S NRP

‑

ZK8:

a) Insert this connector into one of the sensor ports of the R&S NRX.

3. Connect the RF connector of the R&S power sensor to the signal source. For

details, see the user manual of the R&S power sensor.

Note:

Incorrectly connecting/disconnecting an R&S power sensor can damage the

power sensor or lead to erroneous results.

Preparing for Use

www.allice.de

Allice Messtechnik GmbH

Содержание 1424.7005.02



































































































































































































































































































































































































































































































































Результаты поиска

Содержание 1424.7005.02

Отзывы:

Похожие инструкции для 1424.7005.02

Бренды по названию

Популярные бренды

R&S 1424.7005.02, Руководство пользователя

Результаты поиска

Содержание 1424.7005.02

Отзывы:

Похожие инструкции для 1424.7005.02

Бренды по названию

Популярные бренды