RAM 1500 CLASSIC 2020 Скачать руководство пользователя страница 240 | Manualshive

Страница: 240 / 360

background image

238

IN CASE OF EMERGENCY

TOWING A DISABLED VEHICLE

This section describes procedures for towing a disabled vehicle using a commercial towing service. If the transmission and drivetrain are operable, disabled

vehicles may also be towed as described under “Recreational Towing” in the “Starting And Operating” section.

Proper towing or lifting equipment is required to

prevent damage to your vehicle. Use only tow bars

and other equipment designed for this purpose,

following equipment manufacturer’s instructions.

Use of safety chains is mandatory. Attach a tow bar

or other towing device to main structural members

of the vehicle, not to bumpers or associated

brackets. State and local laws regarding vehicles

under tow must be observed.

If you must use the accessories (wipers,

defrosters, etc.) while being towed, the ignition

must be in the ON/RUN mode, not the ACC mode.
If the key fob is unavailable or the vehicle's battery

is discharged, refer to ”Manual Park Release” or

“Gear Selector Override” in this section for

instructions on shifting the automatic transmission

out of PARK for towing.

Towing Condition

Wheels OFF The Ground

2WD Models

4WD Models

Flat Tow

NONE

If transmission is operable:
• Transmission in NEUTRAL (N)
• 30 mph (48 km/h) max speed
• 15 miles (24 km) max distance

(6–speed transmission)
• 30 miles (48 km) max distance

(8–speed transmission)

See instructions in “Recreational

Towing (Behind Motorhome, Etc.)”

under “Starting And Operating”
• Automatic Transmission in PARK (P)
• Transfer Case in NEUTRAL (N)
• Tow in forward direction

Wheel Lift Or Dolly Tow

Front

NOT ALLOWED

Rear

OK

NOT ALLOWED

Flatbed

ALL

BEST METHOD

BEST METHOD

CAUTION!



Do not use sling type equipment when towing.

Vehicle damage may occur.



When securing the vehicle to a flat bed truck,

do not attach to front or rear suspension

components. Damage to your vehicle may

result from improper towing.

20_DS_OM_EN_USC_t.book Page 238

«
...
238
239
240
241
242
...
»

Содержание 1500 CLASSIC 2020









































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1500 CLASSIC 2020

Бренд: Xblitz Страницы: 16

ANDROID INTERFACE

Бренд: GMC Страницы: 18

Бренд: Prorack Страницы: 15

Бренд: Dacia Страницы: 238

Бренд: TBC Страницы: 12

Бренд: Prorack Страницы: 14

Бренд: Van Guard Страницы: 3

Бренд: Flash Cover Страницы: 2

Бренд: Whispbar Страницы: 17

Бренд: Park-Daddy Страницы: 22

Бренд: RAM Страницы: 496

XEBRA ZAPCAR Series

Бренд: Zap Страницы: 16

1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P

Бренд: Havis-Shields Страницы: 1

Бренд: rough country Страницы: 4

Бренд: Joie Страницы: 53

Bluetooth Kit3 PLUS

Бренд: N-Com Страницы: 36

Бренд: Horn Tools Страницы: 12

Бренд: Toyota Страницы: 285

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды