RAM 1500 2023 страница 114 Скачать руководство пользователя

Страница: 114 / 416

112

GETTING TO KNOW YOUR INSTRUMENT PANEL

Rear Axle Locker Fault Warning Light —

If Equipped

This warning light will illuminate to indicate

when a rear axle locker fault has been

detected.

Service Forward Collision Warning (FCW)

Light — If Equipped

This warning light will illuminate to indicate a

fault in the FCW System. Contact an authorized

dealer for service

page 274.

Service Stop/Start System Warning Light —

If Equipped

This warning light will illuminate when the

Stop/Start system is not functioning properly

and service is required. Contact an authorized

dealer for service.

Service 4WD Warning Light — If Equipped

This warning light will illuminate to signal a fault

with the 4WD system. If the light stays on or

comes on during driving, it means that the 4WD

system is not functioning properly and that

service is required. We recommend you drive to the

nearest service center and have the vehicle serviced

immediately.

Cruise Control Fault Warning Light

This warning light will illuminate to indicate the

Cruise Control System is not functioning

properly and service is required. Contact an

authorized dealer.

Tire Pressure Monitoring System (TPMS)

Warning Light

The warning light switches on and a message is

displayed to indicate that the tire pressure is

lower than the recommended value and/or

that slow pressure loss is occurring. In these

cases, optimal tire duration and fuel consumption may not

be guaranteed.
Should one or more tires be in the condition previously

mentioned, the display will show the indications

corresponding to each tire.

Each tire, including the spare (if provided), should be

checked monthly when cold and inflated to the inflation

pressure recommended by the vehicle manufacturer on

the vehicle placard or tire inflation pressure label. If your

vehicle has tires of a different size than the size indicated

on the vehicle placard or tire inflation pressure label, you

should determine the proper tire inflation pressure for

those tires.
As an added safety feature, your vehicle has been

equipped with a TPMS that illuminates a low tire pressure

telltale when one or more of your tires is significantly

underinflated. Accordingly, when the low tire pressure

telltale illuminates, you should stop and check your tires

as soon as possible, and inflate them to the proper

pressure. Driving on a significantly underinflated tire

causes the tire to overheat and can lead to tire failure.

Underinflation also reduces fuel efficiency and tire tread

life, and may affect the vehicle’s handling and stopping

ability.
Please note that the TPMS is not a substitute for proper

tire maintenance, and it is the driver’s responsibility to

maintain correct tire pressure, even if underinflation has

not reached the level to trigger illumination of the TPMS

low tire pressure telltale.

CAUTION!

Prolonged driving with the Malfunction Indicator Light

(MIL) on could cause damage to the vehicle control

system. It also could affect fuel economy and

driveability. If the MIL is flashing, severe catalytic

converter damage and power loss will soon occur.

Immediate service is required.

CAUTION!

Do not continue driving with one or more flat tires as

handling may be compromised. Stop the vehicle,

avoiding sharp braking and steering. If a tire puncture

occurs, repair immediately using the dedicated tire

repair kit and contact an authorized dealer as soon as

possible.

23_DT_OM_EN_USC_t.book Page 112

Содержание 1500 2023

































































































































































































































































































































































































































Результаты поиска

Содержание 1500 2023

Отзывы:

Похожие инструкции для 1500 2023

Бренды по названию

Популярные бренды

RAM 1500 2023, Руководство пользователя

Результаты поиска

Содержание 1500 2023

Отзывы:

Похожие инструкции для 1500 2023

Бренды по названию

Популярные бренды