RAM 1500 2023 страница 344 Скачать руководство пользователя

Страница: 344 / 416

342

SERVICING AND MAINTENANCE

Synthetic Engine Oils

Your engine was designed for synthetic engine oils, only

use synthetic API approved engine oils.
Synthetic engine oils which do not have both the correct

API trademark and the correct SAE viscosity grade

numbers should not be used.

Materials Added To Engine Oil

The manufacturer strongly recommends against the

addition of any additives (other than leak detection dyes)

to the engine oil. Engine oil is an engineered product and

its performance may be impaired by supplemental

additives.

Disposing Of Used Engine Oil And Oil

Filters

Care should be taken in disposing of used engine oil and

oil filters from your vehicle. Used oil and oil filters,

indiscriminately discarded, can present a problem to the

environment. Contact an authorized dealer, service

station or governmental agency for advice on how and

where used oil and oil filters can be safely discarded in

your area.

NGINE

ILTER

The engine oil filter should be replaced with a new filter at

every engine oil change.

Engine Oil Filter Selection
A full-flow type disposable oil filter should be used for

replacement. The quality of replacement filters varies

considerably. Only high quality Mopar® certified filters

should be used. If a Mopar® Engine Oil Filter is

unavailable, only use filters that meet or exceed

SAE/USCAR-36 Filter Performance Requirements.

NGINE

LEANER

ILTER

For the proper maintenance intervals

page 334.

Engine Air Cleaner Filter Selection
The quality of replacement filters varies considerably.

Only high quality Mopar® certified filters should be used.

Engine Air Cleaner Filter Inspection And

Replacement — Except G/T Model

Engine Air Cleaner Filter Removal
1. With suitable tool fully loosen (six) fasteners on the

engine air cleaner filter cover.

Engine Air Cleaner Filter

2. Lift the engine air cleaner filter cover to access the

engine air cleaner filter.

WARNING!

The air induction system (air cleaner, hoses, etc.) can

provide a measure of protection in the case of engine

backfire. Do not remove the air induction system

(air cleaner, hoses, etc.) unless such removal is

necessary for repair or maintenance. Make sure that no

one is near the engine compartment before starting the

vehicle with the air induction system (air cleaner, hoses,

etc.) removed. Failure to do so can result in serious

personal injury.

1 — Fasteners
2 — Engine Air Cleaner Filter Cover

23_DT_OM_EN_USC_t.book Page 342

Содержание 1500 2023

































































































































































































































































































































































































































Результаты поиска

Содержание 1500 2023

Отзывы:

Похожие инструкции для 1500 2023

Бренды по названию

Популярные бренды

RAM 1500 2023, Руководство пользователя

Результаты поиска

Содержание 1500 2023

Отзывы:

Похожие инструкции для 1500 2023

Бренды по названию

Популярные бренды