RAM 1500 2023 Скачать руководство пользователя страница 319

Страница: 319 / 416

IN CASE OF EMERGENCY

317

NOTE:



Your vehicle may be transmitting data as authorized by

the subscriber.



Never place anything on or near the vehicle’s LTE

(voice/data) or 4G (data) and GPS antennas. You could

prevent LTE (voice/data) or 4G (data) and GPS signal

reception, which can prevent your vehicle from placing

an emergency call. An operable LTE (voice/data) or 4G

(data) network connection and a GPS signal is required

for the SOS Call system to function properly.

NOTE:

Changes or modifications not expressly approved by the

party responsible for compliance could void the user's

authority to operate the equipment.
Automatic SOS — If Equipped
Automatic SOS is a hands-free safety service that can

immediately connect you with help in the event that your

vehicle’s airbags deploy. Please refer to your provided

radio supplement for complete information.

JACKING AND TIRE CHANGING

Use this QR code to access your digital

experience.

NOTE:

If your vehicle is equipped with an air suspension system,

there is a feature which allows the automatic leveling to be

disabled to assist with changing a tire. This feature can be

activated through the Uconnect system

page 209.

REPARATIONS

ACKING

NOTE:

If your vehicle is equipped with Air Suspension, you will

need to enable Tire Jack Mode in the Uconnect system

before changing the tire

page 134.

1. Park on a firm, level surface. Avoid ice or slippery

areas.

2. Turn on the Hazard Warning Flashers.
3. Apply the parking brake.
4. Shift the transmission into PARK (P).
5. Turn the ignition OFF.

WARNING!



Do not attempt to change a tire on the side of the

vehicle close to moving traffic. Pull far enough off the

road to avoid the danger of being hit when operating

the jack or changing the wheel.



Being under a jacked-up vehicle is dangerous. The

vehicle could slip off the jack and fall on you. You

could be crushed. Never put any part of your body

under a vehicle that is on a jack. If you need to get

under a raised vehicle, take it to a service center

where it can be raised on a lift.



Never start or run the engine while the vehicle is on

a jack.



The jack is designed to be used as a tool for changing

tires only. The jack should not be used to lift the

vehicle for service purposes. The vehicle should be

jacked on a firm level surface only. Avoid ice or slip

pery areas.

WARNING!

Do not attempt to change a tire on the side of the

vehicle close to moving traffic. Pull far enough off the

road to avoid being hit when operating the jack or

changing the wheel.

23_DT_OM_EN_USC_t.book Page 317

Содержание 1500 2023

































































































































































































































































































































































































































Результаты поиска

Содержание 1500 2023

Отзывы:

RAM 1500 2023, Руководство пользователя, Страница: 319 / 416

Результаты поиска

Содержание 1500 2023

Отзывы: