RAM 1500 2023 страница 179 Скачать руководство пользователя

Страница: 179 / 416

STARTING AND OPERATING

177

Consider the following items when computing the weight

on the rear axle of the vehicle:



The tongue weight of the trailer.



The weight of any other type of cargo or equipment put

in or on your vehicle.



The weight of the driver and all passengers.

NOTE:

Remember that everything put into or on the trailer adds

to the load on your vehicle. Also, additional

factory-installed options or dealer-installed options must

be considered as part of the total load on your vehicle.

Refer to the Tire And Loading Information Placard for the

maximum combined weight of occupants and cargo for

your vehicle.

RAILER

EVERSE

TEERING

ONTROL

— I

QUIPPED

Feature Overview
Trailer Reverse Steering Control (TRSC) is a feature that

will assist the driver when backing up a trailer. By turning

the knob located on the center stack, you can more

accurately control the direction the trailer will go.

The driver controls the accelerator and the brake while

steering with the use of the Trailer Reverse Steering

Control knob. The trailer is steered according to the

direction the knob is turned.
This feature will also allow the driver to back up a vehicle

and trailer in a straight line when the knob is rested in its

center position.
Minimal setup is required to use this feature.
Set Up:
To use the system, hitch your trailer to the truck and

ensure all electrical wiring is connected

page 182.

The system will automatically calibrate an attached trailer

during normal forward driving with no additional action

needed from the driver. If the vehicle has not had enough

time to automatically calibrate after connecting a trailer,

you will see a “Calibrate Trailer” message in the

instrument cluster when pressing the TRSC button to

activate the system. If this is the case, perform the

following maneuver to calibrate the trailer:
Drive forward at least 100 ft (30 m), perform a 90 degree

turn and return to a straight position for at least another

100 ft (30 m). Perform another 90 degree turn, followed

by another straight drive of at least 100 ft (30 m). Check

that the system has calibrated by pushing the TRSC

button.

NOTE:

The 90 degree turns could be in either the left or right

direction.

Trailer Reverse Steering Control Calibration

1 — Straight 100 ft (30 m)
2 — Intersection turn with radius 50-65 ft (15-20 m) in

either direction
3 — Straight 100 ft (30 m)
4 — Intersection turn with radius 50-65 ft (15-20 m) in

either direction
5 — Straight 100 ft (30 m)
6 — Straight 100 ft (30 m), making sure to align

vehicle/trailer to path center line
7 — Feature is active, turn knob left or right to back the

trailer up

23_DT_OM_EN_USC_t.book Page 177

Содержание 1500 2023

































































































































































































































































































































































































































Результаты поиска

Содержание 1500 2023

Отзывы:

Похожие инструкции для 1500 2023

Бренды по названию

Популярные бренды

RAM 1500 2023, Руководство пользователя

Результаты поиска

Содержание 1500 2023

Отзывы:

Похожие инструкции для 1500 2023

Бренды по названию

Популярные бренды