RAM 1500 2023 страница 123 Скачать руководство пользователя

Страница: 123 / 416

STARTING AND OPERATING

121

(Continued)

NGINE

AILS

TART

If the engine fails to start after you have followed the

“Normal Starting” procedure and the vehicle has not

experienced an Extended Park condition as defined

above, it may be flooded. Push the accelerator pedal all

the way to the floor and hold it there while the engine is

cranking. This should clear any excess fuel in case the

engine is flooded.
The starter motor will engage automatically, run for 10

seconds, and then disengage. Once this occurs, release

the accelerator pedal and the brake pedal, wait 10 to 15

seconds, then repeat the “Normal Starting” procedure.

If the engine has been flooded, it may start to run, but not

have enough power to continue running when the ignition

button/key is released. If this occurs, continue cranking

with the accelerator pedal pushed all the way to the floor.

Release the accelerator pedal and the ignition button/key

once the engine is running smoothly.
If the engine shows no sign of starting after a 10 second

period of engine cranking with the accelerator pedal held

to the floor, wait 10 to 15 seconds, then repeat the

“Normal Starting” procedure.

FTER

TARTING

The idle speed is controlled automatically, and it will

decrease as the engine warms up.

ENGINE BLOCK HEATER — IF EQUIPPED

Engine Block Heater Cord Location

The engine block heater warms engine coolant and

permits quicker starts in cold weather. Connect the heater

cord to a ground-fault interrupter protected 110–115 Volt

AC electrical outlet with a grounded, three-wire extension

cord.
To ensure reliable starting at these temperatures, use of

an externally powered electric engine block heater

(available from an authorized dealer) is recommended.
The engine block heater cord is routed under the hood on

the passenger side of the vehicle next to the engine

coolant reservoir.

WARNING!



Never pour fuel or other flammable liquid into the

throttle body air inlet opening in an attempt to start

the vehicle. This could result in flash fire causing

serious personal injury.



Do not attempt to push or tow your vehicle to get it

started. Vehicles equipped with an automatic trans

mission cannot be started this way. Unburned fuel

could enter the catalytic converter and once the

engine has started, ignite and damage the converter

and vehicle.



If the vehicle has a discharged battery, booster

cables may be used to obtain a start from a booster

battery or the battery in another vehicle. This type of

start can be dangerous if done improperly

page 325.

CAUTION!

To prevent damage to the starter, do not crank the

engine for more than 10 seconds at a time.

Wait 10 to 15 seconds before trying again.

WARNING!

Remember to disconnect the engine block heater cord

before driving. Damage to the 110-115 Volt electrical

cord could cause electrocution.

23_DT_OM_EN_USC_t.book Page 121

Содержание 1500 2023

































































































































































































































































































































































































































Результаты поиска

Содержание 1500 2023

Отзывы:

Похожие инструкции для 1500 2023

Бренды по названию

Популярные бренды

RAM 1500 2023, Руководство пользователя

Результаты поиска

Содержание 1500 2023

Отзывы:

Похожие инструкции для 1500 2023

Бренды по названию

Популярные бренды