RAM Commercial Chassis Cab 2017 Скачать руководство пользователя страница 457 | Manualshive

Страница: 457 / 542

background image

Loose Fuel Filler Cap Message

If the vehicle diagnostic system determines that
the fuel filler cap is loose, improperly installed,
or damaged, a loose gascap indicator will dis-
play in the instrument cluster telltale display

area. Refer to “Instrument Cluster Display” in “Under-
standing Your Instrument Panel” for further information.
Tighten the fuel filler cap properly and push the SELECT
button to turn off the message. If the problem continues,
the message will appear the next time the vehicle is started.

A loose, improperly installed, or damaged fuel filler cap
may also turn on the Malfunction Indicator Light (MIL).

EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS

In some localities, it may be a legal requirement to pass an
inspection of your vehicle’s emissions control system.
Failure to pass could prevent vehicle registration.

For states that require an Inspection and Mainte-
nance (I/M), this check verifies the “Malfunction
Indicator Light (MIL)” is functioning and is not on

when the engine is running, and that the OBD II system is

ready

for testing.

Normally, the OBD II system will be

ready

. The OBD II

system may

not

be ready if your vehicle was recently

serviced, or recently had a dead battery or a battery
replacement. If the OBD II system should be determined

not ready

for the I/M test, your vehicle may fail the test.

Your vehicle has a simple ignition actuated test, which you
can use prior to going to the test station. To check if your
vehicle’s OBD II system is

ready

, you must do the following:

1. Cycle the ignition to the ON mode, but do not crank or

start the engine.

NOTE:

If you crank or start the engine, you will have to

start this test over.

2. As soon as you cycle the ignition to the ON mode, you

will see the “Malfunction Indicator Light (MIL)” symbol
come on as part of a normal bulb check.

3. Approximately 15 seconds later, one of two things will

happen:

•

The MIL will flash for about 10 seconds and then return
to being fully illuminated until you cycle the ignition
OFF or start the engine. This means that your vehicle’s
OBD II system is

not ready

and you should

not

proceed

to the I/M station.

7

MAINTAINING YOUR VEHICLE

455

«
...
455
456
457
458
459
...
»

Содержание Chassis Cab 2017































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chassis Cab 2017

Бренд: JAC Страницы: 70

Бренд: Samsung Страницы: 133

Бренд: AA Products Страницы: 6

Бренд: Jeep Страницы: 673

PICASSO XSARA DESIRE 1.6 - MESUREMENT

Бренд: CITROEN Страницы: 2

YARIS LIFTBACK 2009

Бренд: Toyota Страницы: 13

Бренд: Westfalia Страницы: 71

Бренд: Mercedes-Benz Страницы: 54

Бренд: Draw tite Страницы: 4

Бренд: Mercedes-Benz Страницы: 329

Evo All THAR-FOR3

Бренд: Fortin Страницы: 7

Бренд: Toyota Страницы: 636

Бренд: Warn Страницы: 5

Бренд: Fab Fours Страницы: 21

2011 SRX CROSSOVER

Бренд: Cadillac Страницы: 416

Бренд: TIE DOWN Страницы: 2

Бренд: Tesla Страницы: 274

Бренд: Buick Страницы: 371

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды