RAM Commercial Chassis Cab 2017 Скачать руководство пользователя | Manualshive

Страница: 407 / 542

background image

Fuel System Cautions

CAUTION!

Follow these guidelines to maintain your vehicle’s
performance:

•

The use of leaded gasoline is prohibited by Federal
law. Using leaded gasoline can impair engine perfor-
mance and damage the emissions control system.

•

An out-of-tune engine or certain fuel or ignition
malfunctions can cause the catalytic converter to
overheat. If you notice a pungent burning odor or
some light smoke, your engine may be out of tune or
malfunctioning and may require immediate service.
Contact your authorized dealer for service assistance.

•

The use of fuel additives, which are now being sold
as octane enhancers, is not recommended. Most of
these products contain high concentrations of metha-
nol. Fuel system damage or vehicle performance
problems resulting from the use of such fuels or
additives is not the responsibility of the manufac-
turer and may void or not be covered under the New
Vehicle Limited Warranty.

NOTE:

Intentional tampering with the emissions control

system can result in civil penalties being assessed against
you.

Carbon Monoxide Warnings

WARNING!

Carbon monoxide (CO) in exhaust gases is deadly.
Follow the precautions below to prevent carbon mon-
oxide poisoning:

•

Do not inhale exhaust gases. They contain carbon
monoxide, a colorless and odorless gas, which can
kill. Never run the engine in a closed area, such as a
garage, and never sit in a parked vehicle with the
engine running for an extended period. If the vehicle
is stopped in an open area with the engine running
for more than a short period, adjust the ventilation
system to force fresh, outside air into the vehicle.

•

Guard against carbon monoxide with proper main-
tenance. Have the exhaust system inspected every
time the vehicle is raised. Have any abnormal condi-
tions repaired promptly. Until repaired, drive with
all side windows fully open.

5

STARTING AND OPERATING

405

«
...
405
406
407
408
409
...
»

Содержание Chassis Cab 2017































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chassis Cab 2017

Бренд: Alpine Страницы: 2

Бренд: Whispbar Страницы: 15

Бренд: Jeep Страницы: 16

Бренд: Audi Страницы: 4

Parrot MKi + ParrotCK3100 range LOGAN

Бренд: Parrot Страницы: 10

Бренд: Cadillac Страницы: 409

Бренд: Fortin Страницы: 9

Бренд: KEKO Страницы: 3

Бренд: Movon Страницы: 43

Бренд: Softride Страницы: 4

Бренд: Club Car Страницы: 286

Бренд: Acura Страницы: 7

Бренд: Fabbri Страницы: 32

Бренд: Whelen Engineering Company Страницы: 2

Бренд: KAP Страницы: 22

2002 Accord Coupe

Бренд: Honda Страницы: 367

Бренд: APS Страницы: 4

Бренд: Metra Electronics Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды