RAM Commercial Chassis Cab 2017 Скачать руководство пользователя | Manualshive

Страница: 328 / 542

background image

Tip Start Feature

Do not

press the accelerator. Cycle the ignition switch

briefly to the START position and release it. The starter
motor will continue to run and will automatically disen-
gage when the engine is running.

Keyless Enter-N-Go — Ignition

This feature allows the driver to operate
the ignition switch with the push of a
button, as long as the Remote Start/
Keyless Enter-N-Go key fob is in the
passenger compartment.

Normal Starting

To Turn On The Engine Using The ENGINE
START/STOP Button

1. The transmission must be in PARK.

2. Press and hold the brake pedal while pushing the

ENGINE START/STOP button once.

3. The system takes over and attempts to start the vehicle.

If the vehicle fails to start, the starter will disengage
automatically after 10 seconds.

4. If you wish to stop the cranking of the engine prior to

the engine starting, push the button again.

NOTE:

Normal starting of either a cold or a warm engine

is obtained without pumping or pressing the accelerator
pedal.

To Turn Off The Engine Using ENGINE
START/STOP Button

1. Place the gear selector in PARK, then push and release

the ENGINE START/STOP button.

2. The ignition switch will return to the OFF position.

3. If the gear selector is not in PARK, the ENGINE START/

STOP button must be held for two seconds or three short
pushes in a row with the vehicle speed above 5 mph
(8 km/h) before the engine will shut off. The ignition
switch position will remain in the ACC position until the
gear selector is in PARK and the button is pushed twice
to the OFF position. If the gear selector is not in PARK
and the ENGINE START/STOP button is pushed once,
the instrument cluster will display a “Vehicle Not In

326

STARTING AND OPERATING

«
...
326
327
328
329
330
...
»

Содержание Chassis Cab 2017































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chassis Cab 2017

Бренд: Davis Instruments Страницы: 16

Бренд: Abarth Страницы: 176

Бренд: Q'STRAINT Страницы: 10

Бренд: RaceChip Страницы: 20

Бренд: Zavoli Страницы: 26

Бренд: Cargo Floor Страницы: 16

Бренд: Axxess Страницы: 8

Бренд: Metra Electronics Страницы: 2

Бренд: TATA Motors Страницы: 92

Sedan CIVIC 2022

Бренд: Honda Страницы: 701

Бренд: Black Horse Off Road Страницы: 7

Бренд: A-Tach Mounts Страницы: 2

2000 9-5 2.3 Turbo Ecopower

Бренд: Saab Страницы: 256

Бренд: Ford Страницы: 8

Бренд: Navman Страницы: 27

Бренд: Hamron Страницы: 6

Бренд: Ranger design Страницы: 6

Tri-Mount 34269

Бренд: PowerMadd Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды