RAM Commercial Chassis Cab 2017 Скачать руководство пользователя | Manualshive

Страница: 327 / 542

background image

STARTING PROCEDURES

Before starting your vehicle, adjust your seat, adjust both
inside and outside mirrors, and fasten your seat belt.

The starter should not be operated for more than 10-second
intervals. Waiting a few seconds between such intervals
will protect the starter from overheating.

WARNING!

•

When leaving the vehicle, always make sure the
keyless ignition node is in the

ⴖ

OFF

ⴖ

mode, remove

the key fob from the vehicle and lock the vehicle.

•

Never leave children alone in a vehicle, or with
access to an unlocked vehicle. Allowing children to
be in a vehicle unattended is dangerous for a number
of reasons. A child or others could be seriously or
fatally injured. Children should be warned not to
touch the parking brake, brake pedal or the gear
selector.

•

Do not leave the key fob in or near the vehicle, or in
a location accessible to children, and do not leave the
ignition of a vehicle equipped with Keyless Enter-
N-Go in the ACC or ON/RUN mode. A child could

(Continued)

WARNING!

(Continued)

operate power windows, other controls, or move the
vehicle.

•

Do not leave children or animals inside parked
vehicles in hot weather. Interior heat build-up may
cause serious injury or death.

Normal Starting

Normal starting of either a warm or cold engine is obtained
without pumping or pressing the accelerator pedal. Cycle
the ignition to the START position and release when the
engine starts. If the engine fails to start within 10 seconds,
cycle the ignition to the OFF position, wait five seconds,
then repeat the “Normal Starting” procedure.

Automatic Transmission

Start the engine with the gear selector in the NEUTRAL or
PARK. Apply the brake before shifting into any driving
range.

NOTE: This vehicle is equipped with a transmission
shift interlocking system. The brake pedal must be
pressed to shift out of PARK.

5

STARTING AND OPERATING

325

«
...
325
326
327
328
329
...
»

Содержание Chassis Cab 2017































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chassis Cab 2017

Titanium Series

Бренд: Fass Страницы: 13

Бренд: J-Top Страницы: 2

AUDI 4G HIGHEND

Бренд: KAP Страницы: 20

Бренд: RAM Страницы: 116

Dodge Charger TufBox

Бренд: TUFLOC Страницы: 6

Бренд: Maserati Страницы: 210

Бренд: OnStar Страницы: 22

PACCAR PACMOBILE 20

Бренд: DAF Страницы: 18

Бренд: Cadillac Страницы: 34

Бренд: BURY Страницы: 2

Бренд: Velleman Страницы: 12

Бренд: Sagem Страницы: 10

Бренд: rough country Страницы: 4

Бренд: Volvo Страницы: 197

FABIA II TMB PS 035

Бренд: Skoda Страницы: 16

1999 Crown Victoria

Бренд: Ford Страницы: 208

Бренд: Blaupunkt Страницы: 6

Outlander Plug-in hybrid

Бренд: Mitsubishi Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды