RAM Commercial Chassis Cab 2017 Скачать руководство пользователя | Manualshive

Страница: 239 / 542

background image

Battery Saver On/Battery Saver Mode Message —
Electrical Load Reduction Actions — If Equipped

This vehicle is equipped with an Intelligent Battery Sensor
(IBS) to perform additional monitoring of the electrical
system and status of the vehicle battery.

In cases when the IBS detects charging system failure, or
the vehicle battery conditions are deteriorating, electrical
load reduction actions will take place to extend the driving
time and distance of the vehicle. This is done by reducing
power to or turning off non-essential electrical loads.

Load reduction is only active when the engine is running.
It will display a message if there is a risk of battery
depletion to the point where the vehicle may stall due to
lack of electrical supply, or will not restart after the current
drive cycle.

When load reduction is activated, the message “Battery
Saver On” or “Battery Saver Mode” will appear in the
instrument cluster.

These messages indicate the vehicle battery has a low state
of charge and continues to lose electrical charge at a rate
that the charging system cannot sustain.

NOTE:

•

The charging system is independent from load reduc-
tion. The charging system performs a diagnostic on the
charging system continuously.

•

If the Battery Charge Warning Light is on it may indicate
a problem with the charging system. Refer to “Battery
Charge Warning Light” in “Understanding Your Instru-
ment Panel” for further information.

The electrical loads that may be switched off (if equipped),
and vehicle functions which can be affected by load
reduction:

•

Heated Seat/Vented Seats/Heated Wheel

•

Heated/Cooled Cup Holders — If Equipped

•

Rear Defroster And Heated Mirrors

•

HVAC System

•

115V AC Power Inverter System

•

Audio and Telematics System

4

UNDERSTANDING YOUR INSTRUMENT PANEL

237

«
...
237
238
239
240
241
...
»

Содержание Chassis Cab 2017































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chassis Cab 2017

Бренд: Oldsmobile Страницы: 360

Бренд: Calix Страницы: 5

Бренд: AA Products Страницы: 4

Бренд: Easee Страницы: 12

Бренд: Hama Страницы: 4

Бренд: Volvo Страницы: 230

Бренд: Brodit Страницы: 2

Бренд: Ecco Страницы: 24

Бренд: Whispbar Страницы: 63

Бренд: Reliant Страницы: 206

Ridesmart KMA-610

Бренд: KlipXtreme Страницы: 12

Бренд: Porsche Страницы: 146

Бренд: Belkin Страницы: 30

Бренд: Mitsubishi Страницы: 141

Бренд: Subaru Страницы: 399

Бренд: Quadratec Страницы: 8

Бренд: GStop Страницы: 28

Бренд: Westfalia Страницы: 97

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды