RAM Commercial Chassis Cab 2017 Скачать руководство пользователя | Manualshive

Страница: 205 / 542

background image

If brake failure is indicated, immediate repair is necessary.

WARNING!

Driving a vehicle with the red brake light on is
dangerous. Part of the brake system may have failed. It
will take longer to stop the vehicle. You could have a
collision. Have the vehicle checked immediately.

Vehicles equipped with the Anti-Lock Brake System (ABS)
are

also

equipped

with

Electronic

Brake

Force

Distribution (EBD).

CAUTION!

In the event of an EBD failure, the Brake Warning
Light will turn on along with the ABS Light. Immedi-
ate repair to the ABS system is required.

Operation of the Brake Warning Light can be checked by
placing the ignition in the ON/RUN position. The light
should illuminate for approximately two seconds. The light
should then turn off unless the parking brake is applied or
a brake fault is detected. If the light does not illuminate,
have the light inspected by an authorized dealer.

The light also will turn on when the parking brake is
applied with the ignition placed in the ON/RUN position.

NOTE:

This light shows only that the parking brake is

applied. It does not show the degree of brake application.

Vehicle Security Warning Light — If Equipped

Red Telltale

Light

What It Means

Vehicle Security Warning Light — If Equipped

This light will flash at a fast rate for approximately 15 seconds when the vehicle security alarm is
arming, and then will flash slowly until the vehicle is disarmed.

4

UNDERSTANDING YOUR INSTRUMENT PANEL

203

«
...
203
204
205
206
207
...
»

Содержание Chassis Cab 2017































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chassis Cab 2017

Бренд: Yakima Страницы: 4

CommCenter D1 Series

Бренд: Federal Signal Corporation Страницы: 16

Cushman Turf Truckster

Бренд: Jacobsen Страницы: 210

Бренд: REVCAMUK Страницы: 4

Бренд: V8 equipment Страницы: 17

Бренд: Saab Страницы: 288

Бренд: Sunsky Страницы: 9

Бренд: FALCON RIDGE Страницы: 7

Бренд: Volvo Страницы: 30

BASIC TLL171231

Бренд: Tellur Страницы: 5

1966 Spider 105

Бренд: Alfa Romeo Страницы: 46

Бренд: FALCON RIDGE Страницы: 4

Бренд: Prorack Страницы: 15

Бренд: Honda Страницы: 22

Бренд: Mercedes-Benz Страницы: 494

Бренд: GROM Audio Страницы: 20

Бренд: Maserati Страницы: 37

Бренд: Westin Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды