RAM Commercial Chassis Cab 2017 Скачать руководство пользователя | Manualshive

Страница: 179 / 542

background image

CAUTION!

(Continued)

•

After the use of high power draw accessories, or long
periods of the vehicle not being started (with acces-
sories still plugged in), the vehicle must be driven a
sufficient length of time to allow the generator to
recharge the vehicle’s battery.

AUXILIARY SWITCHES — IF EQUIPPED

There can be up to five auxiliary switches located in the
lower switch bank of the instrument panel which can be
used to power various electronic devices and PTO (Power
Take Off) – If Equipped. If Power Take Off is equipped, it
will take the place of the fifth Auxiliary switch. Connec-
tions to the switches are found under the hood in the
connectors attached to the auxiliary Power Distribution
Center.

You have the ability to configure the functionality of the
auxiliary switches via the instrument cluster display. All
switches can now be configured for setting the switch type
operation to latching or momentary, power source of either
battery or ignition, and ability to hold last state across key
cycles.

NOTE:

Holding last state conditions are met when switch

type is set to latching and power source is set to ignition.

For further information on using the auxiliary switches,
please refer to the Ram Body Builders Guide by accessing
www.rambodybuilder.com and choosing the appropriate
links.

CIGAR LIGHTER AND ASH RECEIVER — IF
EQUIPPED

A removable ash receiver and cigar lighter are available.
For vehicles with a bench seat, the cupholder tray can be
used to hold the ash receiver.

For vehicles equipped with a floor console, the cupholders
may be used.

POWER INVERTER — IF EQUIPPED

A 115 Volt (150 Watts Maximum) outlet is located on the
center stack of the instrument panel, to the right of the
radio. This outlet can power cellular phones, electronics
and other low power devices requiring power up to
150 Watts. Certain high-end video game consoles will
exceed this power limit, as will most power tools.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

177

«
...
177
178
179
180
181
...
»

Содержание Chassis Cab 2017































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chassis Cab 2017

Бренд: Jabra Страницы: 10

Бренд: AccuAir Страницы: 40

Бренд: Peak Страницы: 10

Бренд: Metra Electronics Страницы: 12

Бренд: Halfords Страницы: 4

FleetMaster Air FW8 Series

Бренд: SAF-HOLLAND Страницы: 20

Бренд: Cadillac Страницы: 20

Бренд: Honda Страницы: 4

SAFESTOP SS0005

Бренд: Pro-gard Страницы: 4

Бренд: Nav TV Страницы: 4

Бренд: THIEYE Страницы: 88

Бренд: PUTCO Страницы: 2

Бренд: FORM FIT Страницы: 2

Бренд: Brodit Страницы: 2

Бренд: Acura Страницы: 4

Бренд: APS Страницы: 4

Бренд: Audiovox Страницы: 2

Giulia 952 2017

Бренд: Alfa Romeo Страницы: 324

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды