RAM Commercial Chassis Cab 2017 Скачать руководство пользователя | Manualshive

Страница: 148 / 542

background image

To Accelerate For Passing

Press the accelerator as you would normally. When the
pedal is released, the vehicle will return to the set speed.

Using Speed Control On Hills

The transmission may downshift on hills to maintain the
vehicle set speed.

NOTE:

The Speed Control system maintains speed up and

down hills. A slight speed change on moderate hills is
normal.

On steep hills, a greater speed loss or gain may occur, it
may be preferable to drive without Speed Control.

WARNING!

Speed Control can be dangerous where the system
cannot maintain a constant speed. Your vehicle could
go too fast for the conditions, and you could lose
control and have an accident. Do not use Speed Control
in heavy traffic or on roads that are winding, icy,
snow-covered or slippery.

PARKSENSE REAR PARK ASSIST — IF EQUIPPED

The ParkSense Rear Park Assist system provides visual and
audible indications of the distance between the rear fascia
and a detected obstacle when backing up, e.g. during a
parking maneuver. Refer to “ParkSense System Usage
Precautions” in this section for limitations of this system
and recommendations.

ParkSense will retain the last system state (enabled or
disabled) from the last ignition cycle when the ignition is
changed to the ON/RUN position.

ParkSense can be active only when the gear selector is in
REVERSE. If ParkSense is enabled at this gear selector
position, the system will remain active until the vehicle
speed is increased to approximately 7 mph (11 km/h) or
above. When in REVERSE and above the system’s operat-
ing speed, a warning will appear within the instrument
cluster display indicating the vehicle speed is too fast. The
system will become active again if the vehicle speed is
decreased to speeds less than approximately 6 mph
(9 km/h).

146

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
146
147
148
149
150
...
»

Содержание Chassis Cab 2017































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chassis Cab 2017

Бренд: Kargo Master Страницы: 5

Yamaha Rhino 660

Бренд: Yamaha Страницы: 3

5TH GEN 4RUNNER

Бренд: Victory 4x4 Страницы: 5

Бренд: Keith Страницы: 2

Бренд: U & Me Brothers Страницы: 6

Бренд: walser Страницы: 24

Бренд: Nuna Страницы: 17

Бренд: v.link Страницы: 21

Akerstroms Tx700

Бренд: LXE Страницы: 146

Бренд: Mont Blanc Страницы: 2

Бренд: Z Flash Страницы: 4

Бренд: V8 equipment Страницы: 34

Бренд: Prime Design Страницы: 8

Бренд: Scosche Страницы: 8

Бренд: Goobay Страницы: 2

Бренд: Kia Страницы: 673

Бренд: Hollywood Racks Страницы: 8

Бренд: Enduro Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды