Rally URCap Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 117

background image

"maxGrip": 3
[...]

"pattern": [

{

"x": 690,
"y": 165,
"r": [0, 180],
"f": 1

},
{

"x": 690,
"y": 455,
"r": [0, 180],
"f": 0

},
{

"x": 690,
"y": 745,
"r": [0, 180],
"f": 0

},
[...]

],

[...]

Figure 92

: positions in a layer type

8.3.5 - Gripper rotation at pickup

By default, the robot will choose the best gripper position when picking up the box(es) from
the conveyor. The possible options are specified by the gripper optimization settings in the
URCap (4-ways, 2-ways, or none).
For specific box positions however, it is possible to enforce a gripper position (the "g" values)
or limit the possible gripper positions the robot can choose from. Any combinations of the
following values are allowed: 0, 90, 180, and 270, where 0 corresponds to the configured
pickup position in the URCap, other values are angles, counterclockwise when seen from
above.

8.3.6 - Left and right pallet layout

Each layout can be defined separately for the left and right pallet position. Even if the left
and right pallets look identical, the order of the boxes can be different.
The default layout (the "pattern" structure) defines the layout for the right pallet. The
alternative layout (the "altPattern" structure) defines the layout for the left pallet. By default -
if no alternative layout is defined - the robot will generate a mirrored layout for the left pallet,
in order to make a symmetric setup.

Version 2.9.1

© Rocketfarm AS 2021. All rights reserved.

102

«
...
100
101
102
103
104
...
»

Содержание URCap






















































































































Отзывы:

Нет отзывов

Похожие инструкции для URCap

Бренд: S&A Страницы: 13

Бренд: S&A Страницы: 15

Бренд: York Страницы: 104

Бренд: Hitachi Страницы: 140

Бренд: Neuton Страницы: 8

Бренд: Acson international Страницы: 99

Бренд: Acson Страницы: 99

Бренд: Daikin Страницы: 36

Бренд: Daikin Страницы: 97

Бренд: dixell Страницы: 32

Бренд: Robur Страницы: 96

Бренд: Raider Страницы: 30

Бренд: HARRISTON INDUSTRIES Страницы: 47

Бренд: CRT Страницы: 40

Бренд: Ryobi Страницы: 16

Бренд: Ryobi Страницы: 20

Бренд: Ryobi Страницы: 34

Бренд: Bally Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды