Raider RD-MS21, Руководство пользователя

Страница: 19 / 94

19
freely. If so, try starting the machine again.
To prevent damaging the motor must be
regularly freed of chips and dust to ensure
correct cooling.
• If the motor suddenly stops while sawing,
let go of the switch immediately. Loosen the
saw blade from the piece of work, after which
sawing can continue.
• Using long cables of too small a diameter
can result in loss of voltage, which can lead to
problems with the motor.
• For a length up to 15 metres a cable must
be used with a diameter of 1.5 mm2.
• For a length of between 15 and 40 metres
a cable must be used with a diameter of 2.5
mm2.
Turn the appliance off immediately in the
event of:
• A faulty mains plug, mains flex or flex
damage.
• A faulty switch.
• Smoke or smell from scorched insulation.
• Seizing of the saw.
7. ASSEMBLY AND ACCESSORIES
Installation of the mitre saw
• Place one extension piece on the right-
hand side of the machine and the other
extension piece on the left-hand side of the
machine.
• Loosen the locking bolts and slide the
guide rods in the openings.
• Tighten the locking bolts again.
• Place the work piece clamp on the left or
rightside of the machine.
• Hold the handgrip and move the saw
slightly downwards and then pull the pin out
slightly so that the machine comes free.
Note: Never use the mitre saw without the
extension pieces supplied. Make sure that
they are correctly mounted.
Mounting the support bracket.
• Mount the support bracket into the slot in
the rear of the base.
• Tighten the screw to secure the support
bracket.
Installation of the machine on a workbench
or on the subframe.
Fig. 5.
This machine is a stationary machine and
for safety reasons must always be firmly
installed and not used for mobile applications.
You can install the machine in two ways:
a. As a stationary machine on a workbench.
In this case the machine must be secured to
the workbench with 4 bolts.
b. As a stationary machine on the
subframe.
In this case the machine must be secured
to the subframe with 4 bolts and the subframe
anchored to the floor or to a floor plate with
dimensions of at least 1 square meter.
Guide fence insert Fig. H, I, J
For safety reasons, this machine is
equipped with a guide fence insert to be used
when using the machine for sawing straight
cross-cuts.
• For sawing straight cross-cuts, the guide
fence insert must remain mounted on the
machine (fig. H).
• For sawing mitre cuts, the guide fence
insert must be removed from the machine as
shown (fig. H).
• For sawing bevel cuts, the guide fence
insert must be removed from the machine as
shown (fig. I+J)..
MOUNTING AND REMOVING THE SAW
BLADE
Fig. A+B
Do not use the machine without the guard.
Mounting
• Pull out the locking knob (3) and raise the
saw head (12).
• Loosen the bracket (29) by removing the
screw (30).
• Raise the guard (6).
• Keep the spindle lock button (7) pressed
and loosen the bolt (19) using the spanner
(20).
• Remove the flanges (21 & 22).
• If necessary, clean the flanges (21 & 22).
• Mount the flange (22).
• Mount the saw blade (5). Make sure that
the arrow on the saw blade points in the same
direction as the arrow on the saw head.
• Mount the flange (21).
• Keep the spindle lock button (7) pressed
and tighten the bolt (19) using the spanner
(20).
• Lower the guard (6).
• Mount the bracket (29) by tightening the
screw (30).
Removing
• Pull out the locking knob (3) and raise the
saw head (12).
• Loosen the bracket (29) by removing the