manualshive.com logo in svg

RadonTec AlphaAir Freshbox 25, Руководство пользователя

Поделиться
Скачать
RadonTec AlphaAir Freshbox 25 Скачать руководство пользователя страница 15

 

15 

 

Manual 

–

 AlphaAir Freshbox 25 Basic 

 7

 

Bedienung und Programmierung

 

 7.1

 

Opening the device

 

Do  not  reach  into  running  fan  motors.  We 
recommend turning off the unit before opening it.

 

The unit door is held on the inside by two magnetic catches, 
while the hinge is located on the right side. To open the unit, 
pull firmly on the slightly protruding door on the left.

 

When closing the door later, make sure that the condensate foil 
in front of the heat exchanger is upright and that both magnets 
snap into place.

 

 7.2

 

Triggering the unit self-test

 

WITH RESET TO FACTORY SETTINGS

 

Since the unit is reset to factory settings during this 
self-test,  please  do  not  perform  it  if  you  have 
received your unit pre-parameterized. Otherwise, the 
settings would be lost and you would have to reset 
them. 

1.

 

To trigger the self-test, stay on the power key for approx. 
9  seconds  until  the  device  has  emitted  4  beeps.  Then 
release the power key.

 

2.

 

As soon as you have released the button, the device will 
give a short beep.

 

Содержание AlphaAir Freshbox 25



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды