RADIXON WiNRADiO EXCALIBUR PRO WR-G33DDC Скачать руководство пользователя страница 74

Страница: 74 / 126

WiNRADiO G33DDC HF Receiver

Cancel marker reference

– this will remove the marker’s referential status

and the differential frequencies will not be displayed for the other markers.

Remove marker at xx.xxx MHz

– this will remove the indicated marker.

Remove marker at xx.xxx MHz

– by selecting this function, this marker will

be deleted.

Tune to marker at xx.xxx MHz

– this will tune the receiver to the marker

frequency.

Clear all markers

– this function removes all markers from the spectrum.

Baseline Level

The wideband spectrum scope makes it possible to adjust the baseline level
using the

Min. Level

control. This adjusts the minimum displayed signal

strength level, and serves to maximize the useful display space in situations
where the noise floor would occupy too large proportion of the displayed
spectrum (for example in noisy environments or with large antennas).

Содержание WiNRADiO EXCALIBUR PRO WR-G33DDC































































































































Результаты поиска

Содержание WiNRADiO EXCALIBUR PRO WR-G33DDC

Отзывы:

Похожие инструкции для WiNRADiO EXCALIBUR PRO WR-G33DDC

Бренды по названию

Популярные бренды

RADIXON WiNRADiO EXCALIBUR PRO WR-G33DDC, Руководство пользователя

Результаты поиска

Содержание WiNRADiO EXCALIBUR PRO WR-G33DDC

Отзывы:

Похожие инструкции для WiNRADiO EXCALIBUR PRO WR-G33DDC

Бренды по названию

Популярные бренды