Radio Shack TAD-268 страница 45 Скачать руководство пользователя

Страница: 45 / 52

Symptom

Cause

Suggestion

The phone’s range de-
creases.

• The antenna on the

base is not adjusted
properly.

• Fully extend the

antenna on the base
and position it vertically
(see “Adjusting the
Base’s Antenna” on
Page 11).

• The handset’s battery

might need recharging.

• Place the handset in

the base to recharge it.

The phone does not work,
or works poorly.

• The handset is too far

away from the base.

• Move the handset

closer to the base.

• The phone’s cord and

the AC adapter are not
connected properly.

• Properly connect the

phone’s cord and AC
adapter.

• The handset’s battery

might need recharging.

• Place the handset in

the base to recharge it

• The antenna on the

base is not adjusted
properly.

• Fully extend the base’s

antenna and position it
vertically.

The TAD does not answer
calls.

• Interference on the

line.

• Contact your local

phone company.

• The TAD is not set to

answer calls.

• Press the button next

to the ANSWER indi-
cator on the base. The
ANSWER indicator
lights.

• Message tape not

installed in TAD.

• Install the message

tape.

• You have not recorded

an outgoing announce-
ment.

• Record an outgoing

announcement.

43-738.fm Page 45 Friday, August 13, 1999 1:51 PM

Содержание TAD-268





















































Результаты поиска

Содержание TAD-268

Отзывы:

Похожие инструкции для TAD-268

Бренды по названию

Популярные бренды

Radio Shack TAD-268, Руководство пользователя

Результаты поиска

Содержание TAD-268

Отзывы:

Похожие инструкции для TAD-268

Бренды по названию

Популярные бренды