Radio Shack TAD-268 страница 2 Скачать руководство пользователя | Manualshive

Страница: 2 / 52

background image

2

This symbol is intended to alert you
to the presence of uninsulated dan-
gerous voltage within the product’s
enclosure that might be of sufficient
magnitude to constitute a risk of
electric shock. Do not open the
product’s case.

This symbol is intended to inform
you that important operating and
maintenance instructions are in-
cluded in the literature accompany-
ing this product.

READ THIS BEFORE
INSTALLATION

We have designed your telephone to
conform to federal regulations, and
you can connect it to most telephone
lines. However, each device that you
connect to the phone line draws power
from the phone line. We refer to this
power draw as the device’s

ringer

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED PERSONNEL.

Warning: To reduce the risk of fire
or shock hazard, do not expose
this product to rain or moisture.

CAUTION

!

!

equivalence number

, or REN. The

REN is shown on the bottom of the
base.

If you are using more than one phone
or other device on the line, add up all
the RENs. If the total is more than five,
your phone might not ring and your
TAD might not answer. In rural areas,
a total REN of three might impair ringer
operation. If ringer operation is im-
paired, disconnect one of the devices
from the line.

FCC STATEMENT

Your TAD complies with Part 68 of

FCC Rules

. You must, upon request,

provide the FCC registration number
and the REN to your phone company.
Both numbers are shown on the bot-
tom of the base.

Note: You must not connect your TAD
to any of the following:

• Coin-operated systems

• Party-line systems

• Most electronic key phone sys-

tems

© 1997 Tandy Corporation.

All Rights Reserved.

Radio Shack is a registered trademark used by Tandy Corporation.

43-738.fm Page 2 Friday, August 13, 1999 1:51 PM

«
1
2
3
4
...
»

Содержание TAD-268





















































Отзывы:

Нет отзывов

Похожие инструкции для TAD-268

Бренд: Panasonic Страницы: 76

Бренд: Panasonic Страницы: 36

DECT1560 Series

Бренд: Uniden Страницы: 64

Бренд: Commax Страницы: 16

Бренд: Olympia Страницы: 26

Бренд: Maximum Страницы: 18

Бренд: Kingtel Страницы: 12

Бренд: Yada Страницы: 14

Бренд: GE Страницы: 2

Бренд: GE Страницы: 96

Бренд: GE Страницы: 1

Бренд: Leviton Страницы: 2

Бренд: Siemens Страницы: 55

Бренд: Siemens Страницы: 56

Бренд: Samsung Страницы: 8

Бренд: Samsung Страницы: 26

Бренд: Samsung Страницы: 25

Бренд: Samsung Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды