RADEMACHER RolloTron Standard Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 48

RADEMACHER RolloTron Standard Скачать руководство пользователя страница 12

12

EN

There is a risk of injury if the obstacle detection is not
working.

◆

The belt must be wound on as evenly as possible to
ensure safe and correct functioning of the obstacle
detection function.

◆

Please ensure that the belt winds as straight and evenly
as possible into the device during its subsequent cycle
after the obstacle detection system has triggered.

Soft-start / Soft-stop

The RolloTron Standard is equipped with a Soft-start /
Soft-stop function. Gentle starting and stopping serves
to protect the belt winder mechanics and the belt.

Obstacle detection

The movement of the belt is monitored. If the roller shut-
ters hit an obstacle in the DOWN (

t

) direction, the belt

will stop moving and the belt winder is switched off.

6.1 Description of safety functions

i

Once the system has switched off, it is no longer
possible to directly operate the drive in the same
direction.

◆

Run the belt winder back in the opposite direction and
remove any possible obstacle.

◆

Subsequently it is possible to operate the drive in the
original direction again.

Overload cut-off

The RolloTron Standard is equipped with an overload
cut-off system.

If the drive jams in the UP (

▲

) cycle (for example, due to

ice), the belt winder will also switch off.

◆

Once the cause for the overload has been rectified,
the drive is fully operational in both directions.

«
...
10
11
12
13
14
...
»

Содержание RolloTron Standard

















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды