RADEMACHER 3650 00 12 Скачать руководство пользователя страница 101

Страница: 101 / 112

101

26.9 Menu 9.8.9 - Configuring the end points of the

tubular motor

You can use the Troll Comfort to configure the end points of a connect-
ed RADEMACHER electronic tubular motor.

◆

[ SET ]

is additionally displayed during the active end point setting

process.

◆

The end point function is only available for RADEMACHER
electronic tubular motors from 2000 onwards.

◆

The end point setting cannot be adjusted for tubular motors con-
nected in parallel.

◆

The end point function is not available when the light
function is activated, see page 98.

The end points will only be stored if:

◆

The tubular motor is allowed to run for at least four seconds before
an end point is reached.

◆

The configuration process is undertaken starting from the end point
that is to be changed.

◆

Check the correct setting of the end

points directly after completing the configuration

process with the help of the operating buttons.

(not available for the Troll Comfort 3D)

Содержание 3650 00 12

















































































































Результаты поиска

Содержание 3650 00 12

Отзывы:

Бренды по названию

Популярные бренды

RADEMACHER 3650 00 12, Инструкция по электрическому подключению и пусконаладке

Результаты поиска

Содержание 3650 00 12

Отзывы:

Бренды по названию

Популярные бренды