background image

Tab. 9.23: ACM switching - 18 GHz according to MSE state

ver. 2.0

MSE degrade [dB] / MSE improve [dB]

RAy3-18

Modulation

Channel

MHz

4096

QAM

2048

QAM

1024

QAM

512

QAM

256

QAM

128

QAM

64

QAM

32

QAM

16

QAM

QPSK

QPSK

_S

1)

-36.6

-33.8

-30.5

-27.6

-24.5

-21.7

-19.0

-14.8

-9.7

-

5

-

-37.6

-34.8

-31.5

-28.6

-25.5

-22.7

-20.0

-15.8

-10.7

-39.8

-36.5

-33.8

-30.6

-27.6

-24.6

-21.7

-19.0

-14.8

-9.7

-

7 &7.5

-

-40.8

-37.5

-34.8

-31.6

-28.6

-25.6

-22.7

-20.0

-15.8

-10.7

-39.8

-36.5

-33.8

-30.6

-27.6

-24.6

-21.8

-19.0

-14.8

-9.7

-

10

-

-40.8

-37.5

-34.8

-31.6

-28.6

-25.6

-22.8

-20.0

-15.8

-10.7

-39.7

-36.5

-33.8

-30.5

-27.6

-24.5

-21.7

-19.0

-14.8

-9.7

-

13.75

-

-40.7

-37.5

-34.8

-31.5

-28.6

-25.5

-22.7

-20.0

-15.8

-10.7

-39.7

-36.5

-33.8

-30.5

-27.6

-24.5

-21.8

-19.1

-14.8

-9.7

-

20

-

-40.7

-37.5

-34.8

-31.5

-28.6

-25.5

-22.8

-20.1

-15.8

-10.7

-39.8

-36.5

-33.8

-30.5

-27.6

-24.6

-21.8

-19.0

-14.8

-9.7

-

27.5 & 30

-

-40.8

-37.5

-34.8

-31.5

-28.6

-25.6

-22.8

-20.0

-15.8

-10.7

-39.7

-36.5

-33.7

-30.5

-27.6

-24.5

-21.8

-19.0

-14.8

-9.7

-

40

-

-40.7

-37.5

-34.7

-31.5

-28.6

-25.5

-22.8

-20.0

-15.8

-10.7

-39.8

-36.5

-33.8

-30.6

-27.7

-24.6

-21.8

-19.1

-14.8

-9.7

-

50

-

-40.8

-37.5

-34.8

-31.6

-28.7

-25.6

-22.8

-20.1

-15.8

-10.7

-39.8

-36.5

-33.8

-30.6

-27.7

-24.6

-21.8

-19.1

-14.8

-9.7

-

55 & 60

-

-40.8

-37.5

-34.8

-31.6

-28.7

-25.6

-22.8

-20.1

-15.8

-10.7

-39.5

-36.3

-33.7

-30.6

-27.8

-24.7

-21.9

-19.2

-14.9

-9.8

-

80

-

-40.5

-37.3

-34.7

-31.6

-28.8

-25.7

-22.9

-20.2

-15.9

-10.8

-39.4

-36.3

-33.7

-30.6

-27.8

-24.8

-22.0

-19.3

-14.9

-9.8

-

100

-

-40.4

-37.3

-34.7

-31.6

-28.8

-25.8

-23

-20.3

-15.9

-10.8

-39.4

-36.3

-33.7

-30.6

-27.8

-24.8

-22.0

-19.3

-14.9

-9.8

-

110

-

-40.4

-37.3

-34.7

-31.6

-28.8

-25.8

-23

-20.3

-15.9

-10.8

1)

Stability optimized (stronger) FEC

215

© RACOM s.r.o. – RAy3 Microwave Link

Technical parameters

Содержание RAy3-11


















































































































































































































































Отзывы: